ASA5510 booting issue ""tftp://10.0.0.20/asa722-k8.bin""

Unanswered Question
Mar 4th, 2008

Hi,

I've ASA 5510 & upgraded new IOS through ROMM after that it was showing below outputs. why it is showing ""tftp://10.0.0.20/asa722-k8.bin" as a file instead of disk:0... Can anyone help me out this issue..

ciscoasa# sh ver

Cisco Adaptive Security Appliance Software Version 7.2(2) <system>

Compiled on Wed 22-Nov-06 14:16 by builders

System image file is "tftp://10.0.0.20/asa722-k8.bin"

Config file at boot was "startup-config"

ciscoasa up 11 secs

Hardware: ASA5510, 256 MB RAM, CPU Pentium 4 Celeron 1600 MHz

Internal ATA Compact Flash, 64MB

BIOS Flash AT49LW080 @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-55x0 on-board accelerator (revision 0x0)

Boot microcode : CNlite-MC-Boot-Cisco-1.2

SSL/IKE microcode: CNlite-MC-IPSEC-Admin-3.03

IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04

0: Ext: Ethernet0/0 : address is 0013.c480.7ce6, irq 9

1: Ext: Ethernet0/1 : address is 0013.c480.7ce7, irq 9

2: Ext: Ethernet0/2 : address is 0013.c480.7ce8, irq 9

3: Ext: Ethernet0/3 : address is 0013.c480.7ce9, irq 9

4: Ext: Management0/0 : address is 0013.c480.7cea, irq 11

5: Int: Not used : irq 11

6: Int: Not used : irq 5

Licensed features for this platform:

Maximum Physical Interfaces : Unlimited

Maximum VLANs : 100

Inside Hosts : Unlimited

Failover : Active/Active

VPN-DES : Enabled

VPN-3DES-AES : Enabled

Security Contexts : 2

GTP/GPRS : Disabled

VPN Peers : 250

WebVPN Peers : 2

This platform has an ASA 5510 Security Plus license.

Serial Number: JMX0938K05Q

Running Activation Key: 0xa1043b53 0xb469aa4c 0x2072adc8 0xaa44ac1c 0x483bd493

Configuration register is 0x1

Configuration has not been modified since last system restart.

================================

ciscoasa# sh flash

Initializing disk0: cache, please wait...Done.

-#- --length-- -----date/time------ path

62853120 bytes available (28672 bytes used)

============

ciscoasa# sh disk0

-#- --length-- -----date/time------ path

62853120 bytes available (28672 bytes used)

In disk 0 it is not showing any file so that while rebooting (after upgrade ios) it is not booting from flash. Following message i got while reboot

2 seconds. 1 seconds.

Launching BootLoader...

Default configuration file contains 1 entry.

Searching / for images to boot.

Error 28: Selected item cannot fit into memory

unable to boot an image

Default configuration file contains 1 entry.

Searching / for images to boot.

Error 28: Selected item cannot fit into memory

unable to boot an image

Failsafe booting engaged.

Default configuration file contains 1 entry.

Searching / for images to boot.

Error 28: Selected item cannot fit into memory

unable to boot an image

ÿ

Booting system, please wait...

Nmi Npx0 Dly P92 Sha0 Kbd0 Cmos Pci Dma0 PrtB Tim Exp Rfsh Geom Mem0 Mem1 Ebda Admgr1 Memmgr1 AdmgrEbda Sha1 Media Smp0 Brd2

CPUID=0F29, Flags=0004

P7INTEL: Test MC - Flags=0004, CPUID=0F29, Rev=002E [Load]

CacheCpu0 CacheBrd0 Driver PostDrv Dma1 Irq1 Vec Brd4 Time0 Kbd1 Speed Vid0 Par Com PciEnum Vid1 Brd6

8 seconds. 7 seconds.

thanks,

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.

Actions

This Discussion