cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1728
Views
0
Helpful
6
Replies

4507r-e error when powering up first time

bkoryus
Level 1
Level 1

I have a new 4507r-e with a WS-X4013+10GE (Supervisor Engine II-Plus-10GE) module in slot 3. When I power up the chassis I get an error condition. I've tried other Sup ii+10g modules & 4507r-e chassis with the same results. The module is compatibly with this series and the ios seems to be valid. Any suggestions.

Thanks,

Bob

*****************************************

Error message (keeps recycling):

Rommon reg: 0x0E004180

############

k2diags version 5.2_b

prod: WS-X4013+10GE part: 73-10178-07 serial: ##########

Power-on-self-test for Module 3: WS-X4013+10GE

Port/Test Status: (. = Pass, F = Fail, U = Untested)

Reset Reason: PowerUp

Cpu Subsystem Tests ...

seeprom: . temperature_sensor: . eobc: .

Port Traffic: L3 Serdes Loopback ...

0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .

12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .

24: . 25: . 26: . 27: . 28: . 29: . 48: . 49: . 50: . 51: .

Local 10GE Port 62: .

Local 10GE Port 63: .

Port Traffic: L2 Serdes Loopback ...

0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .

12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .

24: . 25: . 26: . 27: . 28: . 29: . 48: . 49: . 50: . 51: .

Port Traffic: L2 Asic Loopback ...

0: . 1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: .

12: . 13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: .

24: . 25: . 26: . 27: . 28: . 29: . 48: . 49: . 50: . 51: .

Switch Subsystem Memory ...

1: . 2: . 3: . 4: . 5: . 6: . 7: . 8: . 9: . 10: . 11: . 12: .

13: . 14: . 15: . 16: . 17: . 18: . 19: . 20: . 21: . 22: . 23: . 24: .

25: . 26: . 27: . 28: . 29: . 30: . 31: . 32: . 33: . 34: . 35: . 36: .

37: . 38: . 39: . 40: . 41: . 42: . 43: . 44: . 45: . 46: . 47: . 48: .

49: . 50: . 51: .

Module 3 Passed

Exiting to ios...

Rommon reg: 0x0E000180

##################################

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, Catalyst 4500 L3 Switch Software (cat4500-IPBASE-M), Version 12.2(31)SGA3, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2007 by Cisco Systems, Inc.

Compiled Thu 19-Jul-07 19:11 by hqluong

Image text-base: 0x10000000, data-base: 0x114A99DC

####### ###### ###### ####### ###### ###

# # # # # # # # # ###

# # # # # # # # # ###

##### ###### ###### # # ###### #

# # # # # # # # #

# # # # # # # # # ###

####### # # # # ####### # # ###

Unsupported chassis type 52, system can not boot

Rebooting in 10 seconds...

10 09 08 07 06 05 04 03 02 01 ÿ

1 Accepted Solution

Accepted Solutions

My apologies, I should've caught it earlier. You need 12.2(40)SG for the 4507R-E and the previous link I posted has incorrect information.

Slots 3 and 4 are reserved for supervisor engines only in Cisco Catalyst 4507R-E; Slots 1-2, and 5-7 are reserved for line cards.

This link has the correct information:

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/product_data_sheet0900aecd801792b1.html

HTH,

__

Edison.

View solution in original post

6 Replies 6

Edison Ortiz
Hall of Fame
Hall of Fame

Hi Bob,

Slots 4 and 5 are for supervisor engines only.

Try one of those slots and let us know how it works out.

http://www.cisco.com/en/US/products/ps9296/index.html

HTH,

__

Edison.

Edison,

Yes, sup is located in slot 4. The blades won't slip in any other slots (larger connector). Also slots 4 & 5 are highlighted with sup only.

Thanks,

Bob

Your initial message indicates the Supervisor was inserted in Slot3.

Power-on-self-test for Module 3: WS-X4013+10GE

Port/Test Status: (. = Pass, F = Fail, U = Untested)

Reset Reason: PowerUp

Am I missing something ?

__

Edison.

Hi Edison,

Your not missing anything, I'm probably missing something. But even though the url says slots 4 & 5 are for sups, only 3 & 4 can support a sup module. There are 7 slots in this 4507r-e chassis, slots 3 & 4 are labeled Supervisor (highligted in blue / see attach picture) and inside slots 3 & 4 the backplane connector is too large to support anything other then a superisor (4013+10ge). All of the other slots (including 5) backplane only have a small connector that seems to only supports the line cards (like the 4548 module). i went ahead and only installed the sup in slot 4 and powered it up, and the error message came up(see attachment).

Again, I've attach a picture showing what is labeled on slots 3 & 4 reflecting they support only supervisor modules. Might not be the best picutre, but I think you might be able to make out slot 2 and under it slot 3 & 4 labeled in blue supervisor statement.

Any thoughts?

Thanks,

Bob

My apologies, I should've caught it earlier. You need 12.2(40)SG for the 4507R-E and the previous link I posted has incorrect information.

Slots 3 and 4 are reserved for supervisor engines only in Cisco Catalyst 4507R-E; Slots 1-2, and 5-7 are reserved for line cards.

This link has the correct information:

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps4324/product_data_sheet0900aecd801792b1.html

HTH,

__

Edison.

Edison,

Thanks! I believe that should do it. I will upload the new IOS and the blade and believe I should be ok. Thank you again,

Bob

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Innovations in Cisco Full Stack Observability - A new webinar from Cisco