Cisco 2610 terminal server(no async ports)

Answered Question
Mar 31st, 2008
User Badges:

I got a terminal server with 2 octal cables attached to it. each octal cable has 8 RJ45 plugs. I installed a patch panel today and plug them into the back of the patch panel. I'll use the front panel as Out of Band ports.


However I can't access other device from my terminal server. I used rollover cable between the patch panel and my device. I was thinking maybe the octal cable is already rolled over. here are my partial output.

line 33 48

session-timeout 5

exec-timeout 5 0

flush-at-activation

no exec

transport input all

transport output none

escape-character BREAK

telnet ip-on-break

stopbits 1

flowcontrol hardware





AS05#sh line

Tty Typ Tx/Rx A Modem Roty AccO AccI Uses Noise Overruns Int

0 CTY - - - - - 0 0 0/0 -

* 33 TTY 9600/9600 - - - - - 1 0 0/0 -

* 34 TTY 9600/9600 - - - - - 1 0 0/0 -

35 TTY 9600/9600 - - - - - 0 0 0/0 -

36 TTY 9600/9600 - - - - - 0 0 0/0 -

37 TTY 9600/9600 - - - - - 0 0 0/0 -

38 TTY 9600/9600 - - - - - 0 0 0/0 -

39 TTY 9600/9600 - - - - - 0 0 0/0 -

40 TTY 9600/9600 - - - - - 0 0 0/0 -

41 TTY 9600/9600 - - - - - 0 0 0/0 -

42 TTY 9600/9600 - - - - - 0 0 0/0 -

43 TTY 9600/9600 - - - - - 0 0 0/0 -

44 TTY 9600/9600 - - - - - 0 0 0/0 -

45 TTY 9600/9600 - - - - - 0 0 0/0 -

46 TTY 9600/9600 - - - - - 0 0 0/0 -

47 TTY 9600/9600 - - - - - 0 0 0/0 -

* 48 TTY 9600/9600 - - - - - 1 0 0/0 -

65 AUX 9600/9600 - - - - - 2 0 0/0 -

* 66 VTY - - - - - 7 0 0/0 -

67 VTY - - - - - 4 0 0/0 -

68 VTY - - - - - 0 0 0/0 -

69 VTY - - - - - 0 0 0/0 -

70 VTY - - - - - 0 0 0/0 -


Line(s) not in async mode -or- with no hardware support:

1-32, 49-64



Correct Answer by royalblues about 8 years 11 months ago

The octal cables are already rolled over. you need to use a normal patch cable fron ur patch panel to the device


also configure


ip host R1 2033

ip host R2 2034

ip host R3 2035

ip host R4 2036

ip host R5 2037

ip host R6 2038

for all the lines



Narayan


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Correct Answer
royalblues Tue, 04/01/2008 - 00:09
User Badges:
  • Green, 3000 points or more

The octal cables are already rolled over. you need to use a normal patch cable fron ur patch panel to the device


also configure


ip host R1 2033

ip host R2 2034

ip host R3 2035

ip host R4 2036

ip host R5 2037

ip host R6 2038

for all the lines



Narayan


Actions

This Discussion