04-08-2008 01:17 AM
Hi,
Please can somebody help me with calculating the VoIP parameters jitter,delay,packet loss using rttMon MIB.It gives lots of OID's .But I am not clear enough to pick up which one.
Thanks in advance for the help
04-08-2008 02:59 AM
Hi, I downloaded a sample MRTG script ages ago and tested it on some Catalyst 3550's & 3560's using ip sla (saa). The OID's in the script were:
jitter .1.3.6.1.4.1.9.9.42.1.5.2.1.7.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.17.1
RTT .1.3.6.1.4.1.9.9.42.1.5.2.1.2.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.2.1 & .1.3.6.1.4.1.9.9.42.1.5.2.1.1.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.1.1
Packet loss .1.3.6.1.4.1.9.9.42.1.5.2.1.26.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.27.1
I apologise for my lack of SNMP knowledge in advance....
HTH
Andy
04-08-2008 03:38 AM
Hi,
Thanks for the information.Actually I am also new to this field of Network Management.I am drilling through the OIDs but not getting exactly what to pick up...I am picking up the oids from the rttMonLatestJitter table.
I tried the oids you mentioned.Only the thing is the end .1 which u specified for evry oid it shows no mib information when i query.help me on that to understand
Thanks for the help
04-08-2008 03:44 AM
Hi, as I said apologies for my lack of SNMP knowledge. I can post the MRTG script I used however there isn't much more in it apart from the values to graph:
# SAA POS JITTER
Target[test-saa-posjitter]: .1.3.6.1.4.1.9.9.42.1.5.2.1.7.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.17.1:public@192.168.255.254
Maxbytes[test-saa-posjitter]: 10000
Title[test-saa-posjitter]: SAA MAX Positive jitter
PageTop[test-saa-posjitter]:
ShortLegend[test-saa-posjitter]: ms
YLegend[test-saa-posjitter]: miliseconds
Legend1[test-saa-posjitter]: MAX Positive jitter SD
Legend2[test-saa-posjitter]: MAX Positive jitter DS
LegendI[test-saa-posjitter]: SD:
LegendO[test-saa-posjitter]: DS:
Options[test-saa-posjitter]: growright, gauge, nopercent
# SAA NEG JITTER
Target[test-saa-negjitter]: .1.3.6.1.4.1.9.9.42.1.5.2.1.7.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.17.1:public@192.168.255.254
Maxbytes[test-saa-negjitter]: 10000
Title[test-saa-negjitter]: SAA MAX Negative jitter
PageTop[test-saa-negjitter]:
ShortLegend[test-saa-negjitter]: ms
YLegend[test-saa-negjitter]: miliseconds
Legend1[test-saa-negjitter]: MAX Negative jitter SD
Legend2[test-saa-negjitter]: MAX Negative jitter DS
LegendI[test-saa-negjitter]: SD:
LegendO[test-saa-negjitter]: DS:
Options[test-saa-negjitter]: growright, gauge, nopercent
# SAA RTT
Target[test-saa-rtt]: .1.3.6.1.4.1.9.9.42.1.5.2.1.2.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.2.1:public@192.168.255.254 / .1.3.6.1.4.1.9.9.42.1.5.2.1.1.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.1.1:public@192.168.255.254
Maxbytes[test-saa-rtt]: 10000
Title[test-saa-rtt]: SAA RTT
PageTop[test-saa-rtt]:
ShortLegend[test-saa-rtt]: ms
YLegend[test-saa-rtt]: miliseconds
Legend1[test-saa-rtt]: Latest RTT
Legend2[test-saa-rtt]: Latest RTT
LegendI[test-saa-rtt]: RTT:
LegendO[test-saa-rtt]: RTT:
Options[test-saa-rtt]: growright, gauge, nopercent
# SAA Packet loss
Target[test-saa-pktloss]: .1.3.6.1.4.1.9.9.42.1.5.2.1.26.1&.1.3.6.1.4.1.9.9.42.1.5.2.1.27.1:public@192.168.255.254
Maxbytes[test-saa-pktloss]: 10000
Title[test-saa-pktloss]: SAA Packet loss
PageTop[test-saa-pktloss]:
ShortLegend[test-saa-pktloss]: pkts
YLegend[test-saa-pktloss]: Packets
Legend1[test-saa-pktloss]: Packet loss SD
Legend2[test-saa-pktloss]: Packet loss DS
LegendI[test-saa-pktloss]: SD:
LegendO[test-saa-pktloss]: DS:
Options[test-saa-pktloss]: growright, gauge
Hopefully someone with more a bit more of a clue than me will reply....
Andy
04-08-2008 03:48 AM
Thanks Sir,
That will help me to understand.I will get back to you if I find any difficulty.
Thanks again for help,
Shivani
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: