04-08-2008 02:52 AM - edited 03-15-2019 05:00 AM
Guys,
I wonder, what can be the cause the router
- does not show controller 0/1/0 & 0/1/1 in running-config
- consequently it does not allow to 'conf t | controller e1 0/1/0'
What can be the problem ? Thanks.
---
{ *** Related Information ***
#sh ver
Cisco IOS Software, 2800 Software (C2800NM-ADVIPSERVICESK9-M), Version 12.4(9)T, RELEASE SOFTWARE (fc1)
ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1)
R1 uptime is 16 minutes
System returned to ROM by power-on
System restarted at 10:59:42 UTC Tue Apr 8 2008
System image file is "flash:c2800nm-advipservicesk9-mz.124-9.T.bin"
Cisco 2821 (revision 53.50) with 247808K/14336K bytes of memory.
Processor board ID FCZ1014700H
2 Gigabit Ethernet interfaces
2 Low-speed serial(sync/async) interfaces
2 Channelized (E1 or T1)/PRI ports
1 Virtual Private Network (VPN) Module
2 Voice FXO interfaces
2 Voice FXS interfaces
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
62720K bytes of ATA CompactFlash (Read/Write)
#sh diag
Slot 0:
C2821 Motherboard with 2GE and integrated VPN Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time unknown
Onboard VPN : v2.2.0
EEPROM contents at hardware discovery:
PCB Serial Number : FOC101117EG
Hardware Revision : 1.0
Top Assy. Part Number : 800-26921-01
Board Revision : A0
Deviation Number : 0
Fab Version : 03
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 87
Hardware date code : 20060316
Chassis Serial Number : FCZ1014700H
Chassis MAC Address : 0017.5a66.9790
MAC Address block size : 32
CLEI Code : CNMJ6P0BRB
Product (FRU) Number : CISCO2821
Part Number : 73-8853-03
Version Identifier : V02
EEPROM format version 4
PVDM Slot 0:
32-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card
Hardware Revision : 3.2
Part Number : 73-8539-04
Board Revision : A0
Deviation Number : 0
Fab Version : 03
PCB Serial Number : FOC10103G0J
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Processor type : 00
Product (FRU) Number : PVDM2-32
Version Identifier : NA
EEPROM format version 4
WIC Slot 1:
VWIC2-2MFT-G703 - 2-Port RJ-48 Multiflex Trunk - T1/E1 & G.703
Hardware Revision : 0.0
Top Assy. Part Number : 800-24920-04
Board Revision : C0
Deviation Number : 0
Fab Version : 04
PCB Serial Number : FOC10140L6F
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Product (FRU) Number : VWIC2-2MFT-G703
Version Identifier : V01
EEPROM format version 4
#sh controllers e1
#
}
Solved! Go to Solution.
04-08-2008 02:55 AM
Please configure:
card type e1 1
And the controllers will appear.
Note your IOS is not updated an can present many bugs.
Hope this helps, please rate post if it does!
04-08-2008 02:55 AM
Please configure:
card type e1 1
And the controllers will appear.
Note your IOS is not updated an can present many bugs.
Hope this helps, please rate post if it does!
04-08-2008 03:52 AM
Thanks, Paolo. Bull's-eye advice.
Conf mode 'card type e1 0 1' reveal interfaces.
04-08-2008 04:24 AM
It happens to everyone that configure a vwic2 the very first time.
Thanks for the nice rating and good luck!
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: