04-09-2008 09:14 PM - edited 03-15-2019 09:58 AM
Hi,
i have configured CCME on a router and i am using a VG224 for analog phones.i need to transfer a call from analog to other extensions(analog and ipphones).i have enabled supplementary-services h450.12 and i gave allow connection h323 to h323.these i have done.i am able to transfer calls from ipphones to analog extensions.but what i have to do to transfer analog to analog or analog to ipphone???i have configured VG224 as h323 gateway..please help me....its urgent....
04-10-2008 09:48 AM
You should consider registering your VG224 analog ports as SCCP endpoints in the CCME. This will allow supplementary-services to be extended to these ports. See this document:
http://www.cisco.com/en/US/docs/ios/12_4t/12_4t2/ht1vg224.html
Your other option is to run a the app_h450_transfer tcl script on the VG224. That will allow you to perform hookflash transfers on your analog ports.
For this option, see this document:
http://www.cisco.com/en/US/docs/ios/voice/tcl/developer/guide/tclivrv2_ch2.html
I've done both methods, and I would suggest that you enable SCCP control and let CCME extend the supplementary services.
04-10-2008 09:51 AM
Excellent above information from Adam that I've rated "5".
04-28-2008 04:45 AM
Hi,
i have tried to configure VG224 as a SCCP gateway.what i have done is:
#conf t
#sccp local
#sccp ccm
#sccp
#sccp ccm group
#associate ccm 1 priority 1
#exit
When i have typed the "#show sccp" command;
this message shows....
"sccp parameters are not activated (dspfarm profiles)or not associated with ccm group"
Then i came to know that dsp farm needs to be created.
I have dsp module in CCME router...
But what i have to do to integrate this ....???
Can you please give me the detailed configuration steps...???
i am stuck with this........
please please help me.........
Thanks in advance.........
04-28-2008 05:21 AM
Here is the document which explains to create a dsp farm.
The information in this document is based on these software and hardware versions:
Cisco CallManager version 4.0(1)
Cisco IOS Software Release 12.2(15)T13 IP Plus
Cisco 2651 Gateway
NM-HDV with two Packet Voice DSP Module (PVDM) DSP Single In-line Memory Modules (SIMMS)
HTH
10-01-2008 04:03 AM
Hello,
I am facing the same situation where I have a CCME with VG224 configured as H.323 peer and not SCCP (we had to since we dont have free ports on the CCME).
I wish to initiate a call transfer from an analog phone connected to the VG224 by using the second method (the script, hookflash).
I have downloaded the app-h450-transfer.2.0.0.4.tcl script and copied it to the flash of the VG224.
The following is my configuration on the VG224:
application
service transfer slot0:app-h450-transfer.2.0.0.4.tcl
paramspace english language 1
dial-peer voice 11 pots
corlist incoming BAC-CSS-GSM
corlist outgoing call-Internal
description --- science lab
service transfer
destination-pattern 3341
port 2/1
where the phone is connected to port 2/1
I have loaded the application (call application voice load transfer)
I still can not transfer a call from an analog phone.
Am I missing something in the config?
How did u get it work by using the tcl script?
I would be very thankful if you can help me on this issue.
regards
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: