auto qos in WS-C4507R

Unanswered Question
Apr 29th, 2008

I need knows if this WS-C4507R support the command auto qos voip trust and what is the best way to configure QOS in the LAN.

------------------ show version ------------------

Cisco IOS Software, Catalyst 4000 L3 Switch Software (cat4000-I9S-M), Version 12.2(25)EW, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2004 by Cisco Systems, Inc.

Compiled Fri 10-Dec-04 14:26 by kellythw

ROM: 12.2(20r)EW1

Dagobah Revision 95, Swamp Revision 6

8901SW254 uptime is 1 year, 25 weeks, 3 days, 1 hour, 32 minutes

Uptime for this control processor is 1 year, 25 weeks, 3 days, 1 hour, 32 minutes

System returned to ROM by power-on

System restarted at 10:22:00 UTC Thu Nov 2 2006

System image file is "bootflash:"

cisco WS-C4507R (MPC8245) processor (revision 8) with 524288K bytes of memory.

Processor board ID FOX0851021H

MPC8245 CPU at 400Mhz, Supervisor V

Last reset from PowerUp

8 Virtual Ethernet interfaces

58 Gigabit Ethernet interfaces

511K bytes of non-volatile configuration memory.

Configuration register is 0x2101

Chassis Type : WS-C4507R

Power consumed by backplane : 40 Watts

Mod Ports Card Type Model Serial No.

---+-----+--------------------------------------+------------------+-----------

1 2 Supervisor V 1000BaseX (GBIC) WS-X4516 JAB0905024M

2 2 Supervisor V 1000BaseX (GBIC) WS-X4516 JAB090604EF

3 24 10/100/1000BaseT (RJ45) WS-X4424-GB-RJ45 JAE084501JM

4 24 10/100/1000BaseT (RJ45) WS-X4424-GB-RJ45 JAE08501ZAQ

5 6 1000BaseX (GBIC) WS-X4306-GB JAE1123KT0L

M MAC addresses Hw Fw Sw Status

--+--------------------------------+---+------------+----------------+---------

1 0013.1a1f.3b00 to 0013.1a1f.3b01 2.0 12.2(20r)EW1 12.2(25)EW Ok

2 0013.1a1f.3b02 to 0013.1a1f.3b03 2.0 12.2(20r)EW1 12.2(25)EW, Ok

3 0012.01f1.97e0 to 0012.01f1.97f7 1.6 Ok

4 0012.01f1.ccc0 to 0012.01f1.ccd7 1.6 Ok

5 000e.83a1.c4e8 to 000e.83a1.c4ed 4.3 Ok

------------------ show bootflash: all ------------------

-#- ED ----type---- --crc--- -seek-- nlen -length- ---------date/time--------- name

1 .. image F0AB9628 C4C440 28 12370880 Feb 9 2005 04:23:53 -06:00 cat4000-i9s-mz.122-25.EW.bin

46873536 bytes available (12371008 bytes used)

anyone can help me?

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Joseph W. Doherty Tue, 04/29/2008 - 11:39

I'm unfamiliar with the 4500 series QoS specifically, or whether it supports any auto QoS features, but in general, either a two class model (real-time and BE), or a four class model (e.g. real-time, better than BE, BE and less than BE) model works well. (Many LAN switches that support QoS/CoS, usually only support two or four classes.)

How to use the four class model, real-time traffic, like VoIP in a LLQ class; really important/critical (and hopefully lightweight) traffic, like voice signally, in the better then BE class (minimal bandwidth guarantee sufficient so traffic usually doesn't queue); really bad traffic, like server network backups, in the less than BE class with a minimal bandwidth guarantee (perhaps only 1%); everything else in BE.

[edit]

PS:

The software configuration guides for your IOS version should have a section about QoS.

santiago_figuer... Tue, 04/29/2008 - 12:32

thansk for your reply, can you tell me how to find a configuration guide for my IOS version?

thanks

Actions

This Discussion