05-01-2008 02:25 PM - edited 03-05-2019 10:43 PM
We've enabled auto qos on our 6504 w/sup32-10G on our ws-6148a blades and are receiving the following errors. Is this normal? Code is the latest out: 12.2(33)SXH2, switches are runnin as L2 devices only (no routing):
Warning: rcv cosmap will not be applied in hardware.
To modify rcv cosmap in hardware, all of the interfaces below
must be put into 'trust cos' state:
Gi3/1 Gi3/2 Gi3/3 Gi3/4 Gi3/5 Gi3/6 Gi3/7 Gi3/8 Gi3/9 Gi3/10 Gi3/11 Gi3/12 Gi3/13 Gi3/14 Gi3/15 Gi3/16 Gi3/17 Gi3/18 Gi3/19 Gi3/20 Gi3/21 Gi3/22 Gi3/23 Gi3/24 Gi3/25 Gi3/26 Gi3/27 Gi3/28 Gi3/29 Gi3/30 Gi3/31 Gi3/32 Gi3/33 Gi3/34 Gi3/35 Gi3/36 Gi3/37 Gi3/38 Gi3/39 Gi3/40 Gi3/41 Gi3/42 Gi3/43 Gi3/44 Gi3/45 Gi3/46 Gi3/47 Gi3/48
threshold configured on all 48 ports on slot 3.
Should config changes be made to the cos trust to utilize hardware capabilities?
Thanks,
-Scott
05-07-2008 06:11 AM
Use the "Interface Range" command and try to disable it on all the interfaces on the module.
By default, you should not see the "rcv-queue .." configurations under the interface. In order to remove the configuration,
try the following commands.
Interface range Gi1/1 - 1/12
Mls qos trust cos
No rcv-queue cos-map
No mls qos trust cos
05-07-2008 07:00 AM
Thanks for the suggestion. Below are the current port configuration for an auto qos port with pc/phone, as well as the commands I tried on a set of selective interfaces (G3/1 -2). I get an error regarding the asic. Since we have phone ports requiring auto qos voip cisco-phone intermixed (non sequential) with access only ports (printers, scanners, etc), this may present a problem on the 6500's.
This problem does not exist on the 4500 series chassis. :-/
interface GigabitEthernet3/1
description Test PC and Phone
switchport
switchport access vlan xx
switchport mode access
switchport voice vlan xy
wrr-queue bandwidth 20 100 200
priority-queue queue-limit 5
wrr-queue queue-limit 65 15 15
wrr-queue random-detect min-threshold 1 70 100 100 100 100 100 100 100
wrr-queue random-detect min-threshold 2 70 100 100 100 100 100 100 100
wrr-queue random-detect min-threshold 3 40 40 50 50 60 60 70 70
wrr-queue random-detect max-threshold 1 100 100 100 100 100 100 100 100
wrr-queue random-detect max-threshold 2 100 100 100 100 100 100 100 100
wrr-queue random-detect max-threshold 3 70 70 80 80 90 90 100 100
wrr-queue cos-map 2 1 1 2
wrr-queue cos-map 3 5 3 4
wrr-queue cos-map 3 7 6 7
mls qos trust cos
auto qos voip cisco-phone
spanning-tree portfast
Error message below when int range is attempted on G3/1 -2 (both phone ports):
switch-lab1(config-if-range)#mls qos trust cos
switch-lab1(config-if-range)#no rcv-queue cos-map
Warning: Can't remove cos-map because configuration is used by some other port(s) on this ASIC which has AutoQoS enabled
Warning: Can't remove cos-map because configuration is used by some other port(s) on this ASIC which has AutoQoS enabled
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: