cnf-files

valides007 · ‎05-02-2008

I'm trying to configure a new CME.

every time i load a firmware to cisco 7960 and try to create a cnf it gives this message:

pbx(config)#tftp-server flash:P00307020200.loads

pbx(config)#tftp-server flash:P00307020200.bin

pbx(config)#tftp-server flash:P00307020200.sbn

pbx(config)#telephony-service

pbx(config-telephony)#load 7960-7940 P00307020200

pbx(config-telephony)#create cnf-files

Post-init cnf creation is in progress, pls re-issue this command later

pbx(config-telephony)#create cnf-files

Any idea how to solve this problem?

Pari Thiagasundaram · ‎05-02-2008

Can you verify IP source address and port are configured? Along with max-dns?

The warning message means that you are trying to modify cnf related CLIs while cnf is under construction. Have you tried the command after the "post-init" process has completed the cnf-file construction ?

It looks like a configuration issue to me.

valides007 · ‎05-02-2008

well this is what i did.

I already have a running CME. So i copied the configuration from this unit and paste it in the new CME. Everything seems working fine except the CNF creation.

I have tried the command many times. It seems that the post-init is still in process.

Archant IS · ‎07-10-2008

Did you find a fix for this as i have same situation.

Thanks.

Ayodeji Okanlawon · ‎07-10-2008

I have seen this before. The cme router seems to be stucked in creating the configuration files for the 7960 phones.

If after a while, you still get this prompt, reload the router and you will be fine

Please rate all useful posts

Archant IS · ‎07-11-2008

Hello, ive reloaded several times now, it definately seems stuck. Do you meen wipe and start again?

Thanks

Ayodeji Okanlawon · ‎07-11-2008

can you issue this command on your ccme router...

show telephony-service tftp-bindings

if you hsve configuration files already created for your phones...use the more system command to view the file...

eg if you have a 7960, you should have an output like this from the show telephony-service tftp-bindings

tftp-server system:/its/SEPDEFAULT.cnf

tftp-server system:/its/SEPDEFAULT.cnf alias SEPDefault.cnf

tftp-server system:/its/XMLDefault7960.cnf.xml alias SEP000DBDBEF372.cnf.xml (this represent mac addy of a phone)

to view this file and its content..use the command

more system:/its/XMLDefault7960.cnf.xml

this will help you to see the configuration files.

Please rate all useful posts

Archant IS · ‎07-11-2008

Hello, show telephony-service tftp-bindings doesnt return anything i'm afarid.

Thanks.

Ayodeji Okanlawon · ‎07-11-2008

That means that the router ha not created any configuration files.

May be you should start all over gain, erasing the files in the flash....this may be a long short..

Please rate all useful posts

Archant IS · ‎07-12-2008

Fixed, didnt have ip source-address ... port 2000 in my telephony-service

Thanks

m_chernogorsky · ‎08-08-2008

Did you found any solutions. Have the same issue ?

m_chernogorsky · ‎08-08-2008

I found solutions.

1. configure max-dn, max-ephone

2. configure time (clock set or ntp)

3. ip source-add port

4. load and create cnf

Maybe not all this step is required, but its work.

Thanks ^-)

MasterRu · ‎03-20-2012

I had this error and did the following to resolve it:

Create tftp-server commands with alias
- tftp-server flash:/phone/7940/P00308010200.loads alias P00308010200.loads
- ..... other tftp-server loads as well, noting the alias
Set tftp-server source address
- ip tftp source-interface
Put the following commands under telephony-service
- telephony-service

max-ephones
max-dn
ip source-address
cnf-file location flash:
load
create cnf-files

After this, you should be able to configure your ephone and ephone-dn and watch the phones register. If you enable debug ephone registration and debug tftp events, you can watch it all happen.