Dialer interest traffic

Unanswered Question
May 13th, 2008
User Badges:

Hi,


I tried to setup a dialer to be activated by any traffic but it doesn't work. I tried to generate traffic with ping command.

Bellow is the dialer configuration:


interface Dialer1

ip address negotiated

encapsulation ppp

dialer pool 10

dialer idle-timeout 0

dialer string 0800000000

dialer load-threshold 1 outbound

dialer-group 8

ppp authentication chap callin

ppp chap hostname [email protected]

ppp chap password 0 ******

ppp multilink

ppp timeout multilink link remove 65535

no clns route-cache

!

ip classless

ip route 0.0.0.0 0.0.0.0 Dialer1

no ip http server

!

!

dialer-list 8 protocol ip permit


Thanks for the help,

Guilherme

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Richard Burts Tue, 05/13/2008 - 11:07
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 LAN, WAN

Guilherme


The configuration of dialer 1 does not have any obvious problems. The dialer string is a bit odd but I assume that this is an attempt to hide the real number. I notice that the dialer is assigned to pool 10. What does the ISDN interface say?


Could you post the router config and also post the output of show isdn status?


HTH


Rick

guilherme.bedin Tue, 05/13/2008 - 12:35
User Badges:

Rick,


Yes the dialer string is a fake number.

I am from Brazil and we use E1 here, my configuration for it is:


controller E1 0

framing NO-CRC4

ds0-group 0 timeslots 1-15,17-31 type r2-digital r2-compelled ani

cas-custom 0

country brazil

metering

category 2

answer-signal group-b 1


I don't known what this pool means I took it from an example. Maybe this is the problem?

What I am missing?


thanks,

Guilherme

Richard Burts Tue, 05/13/2008 - 13:41
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 LAN, WAN

Guilherme


Thanks for the additional information. I am not sure that it is enough for me to understand the problem. In my experience you configure the controller (T1 for me, E1 for you) and that relates to the configuration of a serial interface, which then relates to configuration of the dialer interface. Is there a serial interface related to your E1 controller? If so can you post its config?


HTH


Rick

Makarand Chitale Tue, 05/13/2008 - 14:38
User Badges:
  • Cisco Employee,

Since this is CAS signaling, the call out is going to be as a modem call-out. Will need to see the relevant modem configuration and associated line configuration.


The dialer pool will associate with the physical ports using "dialer pool member" command.


debug dialer / debug cas / debug modem is a good starting point.


Thanks, Mak

guilherme.bedin Wed, 05/14/2008 - 04:41
User Badges:

Hi,


I am away from de AS5300 now but what I have for modem configuration is:

line con 0

interface Group-Async1

no ip address

encapsulation ppp

dialer in-band

dialer pool-member 10

ppp multilink

no clns route-cache

group-range 1 120


and I have groupasync:

interface Group-Async1

no ip address

encapsulation ppp

dialer in-band

dialer pool-member 10

ppp multilink

no clns route-cache

group-range 1 120


I am missing the "dialer pool member". Can be a problem? what it does?


thanks,

Guilherme

Actions

This Discussion