Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
342
Views
0
Helpful
5
Replies

dial peer

Go to solution
anitachoi3
Level 1
Level 1

‎05-14-2008 06:21 AM - edited ‎03-17-2019 09:22 PM

Hi,

I have two groups of ANI (calling numbers). "Group A" is 2102xxxx, "group B" is "3100xxxx"

I would like to config "group A" users to make IDD (A to Z) via carrier A

and

I would like to config "group B" users to make IDD (A to Z) via carrier B

two group of users call the same toll free number 8001234.

e.g.

21021234 makes an IDD call, he dials

"8001234 then, 0018861234567" --> carrier A

31001234 makes an IDD call, he dials

"8001234 then, 0018861234567" --> carrier B

I use the "answer-address" to control the incomimg ANI but I fail. any idea how to config the dial peer?

rdgs

Labels:
0 Helpful
1 Accepted Solution

Accepted Solutions
5 Replies 5

Go to solution
paolo bevilacqua
Hall of Fame
Hall of Fame

‎05-14-2008 06:29 AM

You can use two techniques: COR or "steering digits"

On the incoming DP with answer-address, configure either a COR, or translation-profile to add special digits in front of number.

On the outgoing, you create two DP. With cor, each one will have the proper cor setting. With steering digits, you modify destination-pattern to match the special digits, and again a translation-profile to strip the digits.

Hope this helps, please rate post if it does!

0 Helpful

Go to solution
anitachoi3
Level 1
Level 1
In response to paolo bevilacqua

‎05-14-2008 06:41 AM

Hi,

I try following config but fail. any missing?

rdgs

! R1

dial-peer voice 86601 pots

answer-address 2102.

direct-inward-dial

port 6/0:D

prefix 234

!

dial-peer voice 23401 voip

destination-pattern 234.

session protocol sipv2

session target ipv4:192.168.0.1

dtmf-relay rtp-nte digit-drop h245-signal h245-alphanumeric

!

dial-peer voice 86602 pots

answer-address 3100.

direct-inward-dial

port 6/0:D

!

dial-peer voice 86603 voip

destination-pattern 001.

session protocol sipv2

session target ipv4:172.16.1.1

dtmf-relay rtp-nte digit-drop h245-signal h245-alphanumeric

0 Helpful

Go to solution
paolo bevilacqua
Hall of Fame
Hall of Fame
In response to anitachoi3

‎05-14-2008 06:43 AM

It doesn't work because you need to apply one or the other technique I've suggested above, but your config doesn't.

0 Helpful

Go to solution
anitachoi3
Level 1
Level 1
In response to paolo bevilacqua

‎05-14-2008 06:49 AM

hi,

Thanks

How to config "a COR, or translation-profile to add special digits in front of number"

I do not have any idea to config it.

rdgs

0 Helpful
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Customers Also Viewed These Support Documents