cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
833
Views
0
Helpful
11
Replies

"answer-address" not working

Chuan Liu
Level 1
Level 1

Hi,

I have 3 PRA circuits installed on one 3845 router. I want to send calls from certain numbers out to a specific PRA. Following the Cisco doc, I used answer-address command to match the calling number, then trigger a translation-profile that prefixes 2 digits to the called number. Then use a destination-pattern of the prefixed digits to route the call out a specific PRA.

The problem I am having is that 'answer-address' dial-peer is nerver matched, but a dial-peer 1 is used for incoming leg, and so a default PRA is selected.

As there is no wild card used in the answer-address command, is it the best match?

Relative configs are as follows. Please advise any errors I have made.

Thanks in advance.

--------------------------------------

!

voice translation-rule 771

rule 1 /^\([1-9].*\)/ /772\1/

!

voice translation-rule 772

rule 1 /^772/ /0/

!

!

voice translation-profile PSTN-Outgoing

translate called 772

!

voice translation-profile SIP-Incoming

translate called 771

!

dial-peer voice 10 pots

translation-profile outgoing outgoing-calls

service session

destination-pattern .T

direct-inward-dial

port 0/2/1:15

forward-digits all

!

dial-peer voice 9254300 pots

translation-profile outgoing PSTN-Outgoing

service session

destination-pattern 77T

direct-inward-dial

port 0/3/0:15

forward-digits all

!

dial-peer voice 9254311 voip

translation-profile incoming SIP-Incoming

service session

destination-pattern 99254311

notify redirect ip2pots

redirect ip2ip

session protocol sipv2

session target ipv4:A.B.C.D

dtmf-relay rtp-nte

codec g711ulaw

fax-relay sg3-to-g3

fax protocol pass-through g711alaw

no vad

!

dial-peer voice 925431112 voip

translation-profile incoming SIP-Incoming

answer-address 99254311

notify redirect ip2pots

redirect ip2ip

session protocol sipv2

dtmf-relay rtp-nte

codec g711ulaw

fax-relay sg3-to-g3

fax protocol pass-through g711alaw

no vad

-----------------------------------------

1 Accepted Solution

Accepted Solutions

DP 10 I guess ? These are the consequences of not seeing configs in full :(

View solution in original post

11 Replies 11

Brandon Buffin
VIP Alumni
VIP Alumni

Is the DN of the calling phone 99254311?

Brandon

Hi Brandon,

Yes. It is located off a 2811.

Thanks.

Seems fine. Can you shutdown DP 9254311 and enable "debug voip dialpeer", post result here.

Hi, here is the debug voip dialplan output. I am calling 21856588 from 99254311.

042315: May 16 09:18:44.057: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

Calling Number=6421856588, Called Number=6421856588, Peer Info Type=DIALPEER_INFO_SPEECH

042316: May 16 09:18:44.057: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

Match Rule=DP_MATCH_DEST; Called Number=6421856588

042317: May 16 09:18:44.057: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersCore:

Result=Success(0) after DP_MATCH_DEST

042318: May 16 09:18:44.057: //-1/xxxxxxxxxxxx/DPM/dpMatchPeersMoreArg:

Result=SUCCESS(0)

List of Matched Outgoing Dial-peer(s):

1: Dial-peer Tag=10

042319: May 16 09:18:44.057: //-1/52927366882E/DPM/dpAssociateIncomingPeerCore:

Calling Number=99254311, Called Number=6421856588, Voice-Interface=0x0,

Timeout=TRUE, Peer Encap Type=ENCAP_VOIP, Peer Search Type=PEER_TYPE_VOICE,

Peer Info Type=DIALPEER_INFO_SPEECH

042320: May 16 09:18:44.057: //-1/52927366882E/DPM/dpAssociateIncomingPeerCore:

Result=Success(0) after DP_MATCH_INCOMING_DNIS; Incoming Dial-peer=1

042321: May 16 09:18:44.061: //-1/52927366882E/DPM/dpMatchPeersCore:

Calling Number=, Called Number=6421856588, Peer Info Type=DIALPEER_INFO_SPEECH

042322: May 16 09:18:44.061: //-1/52927366882E/DPM/dpMatchPeersCore:

Match Rule=DP_MATCH_DEST; Called Number=6421856588

042323: May 16 09:18:44.061: //-1/52927366882E/DPM/dpMatchPeersCore:

Result=Success(0) after DP_MATCH_DEST

042324: May 16 09:18:44.061: //-1/52927366882E/DPM/dpMatchPeersMoreArg:

Result=SUCCESS(0)

List of Matched Outgoing Dial-peer(s):

1: Dial-peer Tag=10

042325: May 16 09:18:48.616: Modify Nominator =

042326: May 16 09:18:48.616: FAX_TONE_DET

042327: May 16 09:18:48.616: MODEM_TONE_DET

042328: May 16 09:18:48.616: CM_TONE_DET

All possible debugging has been turned off

Cisco managed to change things again behind our back!

Please configure "dial-peer inbound selection sip-trunk". See:

http://www.cisco.com/en/US/docs/ios/12_3t/voice/command/reference/vrht_d1_ps5207_TSD_Products_Command_Reference_Chapter.html#wp1471437

Hope this helps, please rate post if it does!

Hi Paulo,

I am use version c3845-advipservicesk9-mz.124-4.T1.bin. It does not take the command.

I may need to upgrade the IOS.

For a test, can you switch to h.323 ?

Nothing in doc leads to think the "new" rules applies to that protocol too (supremely confusing).

Hi Paulo,

I got it. One DP has a 'incoming called-number .T' command that catches everything. I shutdown this DN and my DP starts working.

Thanks for your help.

DP 10 I guess ? These are the consequences of not seeing configs in full :(

You are right.

Hi,

I also did a 'debug voip ccapi inout', which is attached.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: