cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
297
Views
0
Helpful
2
Replies

cisco2800 /netmeeting voip & PSTN

nkila_lna
Level 1
Level 1

hi

I want to configure my cisco 2811 (IOS ...) in order to place calls between 2 PC with netmeeting (voip) and between 1 PC with netmeeting (voip) and external PSTN thru (FXO) .

Nothing is working at all .

Is there any command to troubleshoot what is happening during these 12 kind of calls ?

and here please find attached the show tech of my cisco 2800 router

regards

thank a lot

2 Replies 2

hello and thanks friend

I used your URL and I made some progress because I can now make call from netmeeting to PSTN however I still can't make any incoming call from Outside PSTN to my PC netmeeting thru my Cisco 2811!!!

so please have a look to my debug display and my SHOW RUN config below in order to help me asap

best regards

++++++++++++++++++++++++++++++++++

Current configuration : 1228 bytes

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname Router

!

boot-start-marker

boot-end-marker

!

enable secret xxx

enable password cisco

!

no aaa new-model

!

resource policy

!

network-clock-participate wic 1

ip cef

!

!

!

!

voice-card 0

no dspfarm

!

!

!

voice service voip

h323

!

!

interface FastEthernet0/0

ip address 10.10.10.10 255.0.0.0

duplex half

speed auto

no mop enabled

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface Serial0/0/0

no ip address

shutdown

clock rate 2000000

--More--

interface BRI0/1/0

no ip address

!

interface BRI0/1/1

no ip address

!

!

!

ip http server

no ip http secure-server

!

!

!

!

!

control-plane

!

!

!

voice-port 0/1/0

!

voice-port 0/1/1

voice-port 0/2/0

!

voice-port 0/2/1

voice-port 0/3/0

!

voice-port 0/3/1

!

dial-peer voice 1 pots

destination-pattern .

direct-inward-dial

port 0/2/0

!

dial-peer voice 2 voip

session target ipv4:10.0.0.3

dtmf-relay h245-signal

codec g711ulaw

++++++++++++++++++++++++++++

debug voip dialpeer all

Log Buffer (4096 bytes):

167: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerSPI:exit@5927

*May 23 19:51:19.887: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

Calling Number=, Called Number=, Voice-Interface=0x46BF2CD0,

Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE,

Peer Info Type=DIALPEER_INFO_SPEECH

*May 23 19:51:19.887: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

Match Rule=DP_MATCH_PORT;

*May 23 19:51:19.887: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

Result=Success(0) after DP_MATCH_PORT; Incoming Dial-peer=1

*May 23 19:51:19.887: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerSPI:exit@5927

*May 23 19:51:23.967: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

Calling Number=, Called Number=, Voice-Interface=0x46BF2CD0,

Timeout=TRUE, Peer Encap Type=ENCAP_VOICE, Peer Search Type=PEER_TYPE_VOICE,

Peer Info Type=DIALPEER_INFO_SPEECH

*May 23 19:51:23.967: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

Match Rule=DP_MATCH_PORT;

*May 23 19:51:23.967: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCore:

Result=Success(0) after DP_MATCH_PORT; Incoming Dial-peer=1

*May 23 19:51:23.967: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerSPI:exit@5927

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: