Boot Error

Unanswered Question
Jun 4th, 2008

Does anyone know what would cause this error?

Equipment is Cisco Wireless Controller 4402

Error:

Basic type or enum can not be nested, error in the tool for h2

Basic type or enum can not be nested, error in the tool for XML_crc_file_size

Value = 481 for XML tag L2-Roam-Configuration is out of range

osapiTaskSaveStack: locking reaper_sleeper by sshpmReceiveTask, rc=0

osapiTaskSaveStack: locking reaper_sleeper by sshpmReceiveTask, rc=0

osapiTaskSaveStack: locking reaper_sleeper by fp_main_task, rc=0

osapiTaskSaveStack: locking reaper_sleeper by DHCP Client Task, rc=0

osapiTaskSaveStack: locking reaper_sleeper by fp_main_task, rc=0

DPCH - Discarded Packet Counter High = 0x0

DPCL - Discarded Packet Counter Low = 0x0

IPCH - Invalid Packet Counter High = 0x0

IPCL - Invalid Packet Counter Low = 0x0

BPCH - Bad Packet Counter High = 0x0

BPCL - Bad Packet Counter Low = 0x0

CTOS - Cell Top of Stack = 0x2c5

CBOS - Cell Bottom of Stack = 0x2c4

CDCNT - Cell Descriptors Counter = 0xffc

CDLMT - Cell Descriptors Limit = 0x200

ISID - Invalid Stream ID = 0x0

CHTF - Credit High Threshold (Fast Ethernet Ports) = 0xfff

CLTF - Credit Low Threshold (Fast Ethernet Ports) = 0x0

CHTG - Credit High Threshold (Gigabit Ethernet Ports) = 0x320

CLTG - Credit Low Threshold (Gigabit Ethernet Ports) = 0x0

CHTS - Credit High Threshold (Stack Port) = 0x320

CLTS - Credit Low Threshold (Stack Port) = 0x0

FGCR - Fabric General Control Register = 0xc30

ISPN - Invalid Stream Port = 0x0

************************************************************

* Start Cisco Crash Handler *

************************************************************

Sys Name: SihleWireless

Model:

Version: 5.0.148.0

Timestamp: Wed Jun 4 14:36:15 2008

signal: 11

pid: 758

TID: 16386

Task Name: fp_main_task

Reason: System Crash

si_signo: 11

si_errno: 0

si_code: 1

si_addr: 0x9421ffe4

timer tcb: 0x1

timer cb: 0x102cb068 ('asSigV1PrintSig+1000')

timer arg1: 0x0

timer arg2: 0x0

------------------------------------------------------------

Analysis of Failure:

Software Failed on instruction located at: 0x0 (Unknown)

This signal was generated in response to a software

attempt to decode address: 0x8000

This error caused trap number 0x7f7f7f7f to be generated.

------------------------------------------------------------

System Stack

Frame 0: 0x100066b4: create_crash_dump+1100

Frame 1: 0x10006488: create_crash_dump+544

Frame 2: 0x100014f0: sigsegv_handler+984

Frame 3: 0x10c0a8c8: __pthread_sighandler_rt+212

Frame 4: 0x301c2c88: ber_int_sb_write+525924376

Frame 5: 0x00000000: Unknown

Frame 6: 0x10d2024c: ber_int_sb_write+970204

Frame 7: 0x1037f398: xml_check_for_XML_root_tag+676

Frame 8: 0x10

Bootloader 4.2.112.0 (Mar 12 2008 - 19:38:43)

Motorola PowerPC ProcessorID=00000000 Rev. PVR=80200020

CPU: 833 MHz

CCB: 333 MHz

DDR: 166 MHz

LBC: 41 MHz

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.

Actions

This Discussion