cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
842
Views
0
Helpful
8
Replies

AS5400 and SIP/H323 Voice calls..............??????????????................

tareqrebhi
Level 1
Level 1

Dears,

Que(1):what signal is output from AS5400.

Does it SIP or H323?

Que(2):i need to generate SIP and H323 Voice calls from AS5400 , can i do that?

if no what are your recommendations for AS5400 to be apple generate SIP and H323 Voice calls for other VoIP carriers?

Que(3): can AS5400 generate voice calls directly to other Carriers as:

AS5400 (calls SIP & H323)------to----- B carries.

any help please.

8 Replies 8

paolo bevilacqua
Hall of Fame
Hall of Fame

1. Both. It is configured as "session protocol" under voip DP.

2. Yes

3. Yes

Hope this helps, please rate post if it does!

Ok man thanks a lot.

i have this issue now:

Dear,

I tried to add new E1 to existed E1s. old E1 has slot time signalling with trunknailed called 1002, I need this New E1 without time signal mean to add to previous trunk 1002.

I added this command:

prov-add:nailedtrnk:name="1033",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="33",dsttimeslot="33",spansize=31

but when I added this new E1 to old E1,old E1 can not send or receive any calls (it is down) beside that new E1 doesn't run, I tried delete it using :

prov-dlt:nailedtrnk:name="1033",srcsvc="ss7p-jtc-abdali",dstsvc="naspath1-abdali",srcspan="ffff",dstspan="0",srctimeslot="33",dsttimeslot="33",spansize=31

I added at AS5400 this commands:

controller E1 7/2

framing NO-CRC4

pri-group timeslots 1-31 nfas_d primary nfas_int 1 nfas_group 1

i delete every thing i put at PGW and AS5400.... but old E1 doesn't come up.

i need to say before adding new E1 every thing is will but after problems appeared, i have 2 E1s were running well now just one live and the other died.

i did blk and unblk at PGW but no changes at channel they still block.

i attached files for more details.

thanks for any help.

Sorry, I can't help with SS7.

thank you

Sir,

to assist you, please send PGW configurations and your objetive: What E1s will be active in AS5400 and what are the SS7 configurations expected to work in this E1: CICs, signaling link been used.

to export PGW configuration, at the MML session, type:

prov-exp:all:dirname="20080815"

where is the name of the directory where the configurations will be saved.

this directory is created under

/opt/CiscoMGC/etc/cust_specific.

the files that interest in this case is the config.mml and the export_trunk.dat.

regards,

Daniel

can please advise me with commands i should use to set AS5400 to originate and terminate voice calls in both SIP and H323?

dears

can you please help if i can use MGCP with AS5400XM or not ???

daniel.fuchs
Level 1
Level 1

Trying to answer your concerns:

1 - yes, it can do h.323, sip and mgcp. you can verify in this link:

http://www.cisco.com/en/US/prod/collateral/iad/ps505/ps6269/product_data_sheet0900aecd802efc92.html

2 - yes, you can.

3 - yes, just be carefull with security.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: