No voice-port 2821 w/HWIC-1CE1T1-PRI and PVDM2-32

Answered Question
Jun 8th, 2008
User Badges:

I am in the middle of setting up a voice gateway and when I try to set up the voice-port, I get "Invalid input".


Applicable config:

controller T1 0/0/0

framing esf

linecode b8zs

cablelength short 110

pri-group timeslots 1-24


interface Serial0/0/0:23

no ip address

encapsulation hdlc

isdn switch-type primary-dms100

isdn incoming-voice voice

isdn map address . plan isdn type national

isdn send-alerting

isdn outgoing ie redirecting-number

isdn outgoing ie high-layer-compat

isdn outgoing ie user-user

no cdp enable

!

Show inventory output:


NAME: "2821 chassis", DESCR: "2821 chassis"

PID: CISCO2821 , VID: V04 , SN: FTX1222A0N3


NAME: "1 port channelized and PRI T1/E1 HWIC on Slot 0 SubSlot 0", DESCR: "1 port channelized and PRI T1/E1 HWIC"

PID: HWIC-1CE1T1-PRI , VID: V01 , SN: FOC12043N5W


NAME: "PVDMII DSP SIMM with Two DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SIMM with Two DSPs"

PID: PVDM2-32 , VID: V01 , SN: FOC12161HE7


I've been trying to figure this out and I've hit a brick wall. I thought I had all the pieces...


Thank you


Correct Answer by Rob Huffman about 8 years 9 months ago

Hi Richard,


The problem here is that the HWIC-1CE1T1-PRI does not support Voice PRI's. :( You will want to use a VWIC.


http://www.cisco.com/en/US/prod/collateral/modules/ps2797/product_data_sheet0900aecd80710c88_ps5949_Products_Data_Sheet.html


Hope this helps! Sorry man,

Rob

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (2 ratings)
Loading.
Paolo Bevilacqua Sun, 06/08/2008 - 15:45
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Show ver? You might be running an image w/o voice support. E.g. ipbase.


Hope this helps, please rate post if it does!

Correct Answer
Rob Huffman Sun, 06/08/2008 - 16:00
User Badges:
  • Super Blue, 32500 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 IP Telephony, Unified Communications

Hi Richard,


The problem here is that the HWIC-1CE1T1-PRI does not support Voice PRI's. :( You will want to use a VWIC.


http://www.cisco.com/en/US/prod/collateral/modules/ps2797/product_data_sheet0900aecd80710c88_ps5949_Products_Data_Sheet.html


Hope this helps! Sorry man,

Rob

Paolo Bevilacqua Sun, 06/08/2008 - 16:04
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Oh, I misread that, I "wanted" to read VWIC and so I did :[


Of course Rob is correct. So 5 points for him here.

Rob Huffman Sun, 06/08/2008 - 17:09
User Badges:
  • Super Blue, 32500 points or more
  • Hall of Fame,

    Founding Member

  • Cisco Designated VIP,

    2017 IP Telephony, Unified Communications

Hi Paolo,


You are most kind! Thanks for this nice vote my friend.


Rock On!

Huff

rmachida Sun, 06/08/2008 - 19:18
User Badges:

Wow, thank you. Not great news but I figured there had to be a good reason.


Thank you all,

Richard

Actions

This Discussion