Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
541
Views
6
Helpful
6
Replies

Please help me to select a Cisco core-switch!

l_masoumi
Level 1
Level 1

‎06-10-2008 12:44 AM - edited ‎03-05-2019 11:31 PM

Hi all,

Anybody can help me to select a proper Cisco Core-Switch?

Some of the needed specifications are below:

1- At least 08 Gbit Ethernet - RG45 copper connector

2- At least 12 fiber gigabit module bases

3- At least 12 Gigabit Ethernet Fiber ports (Populated)

4- Manageable Gigabit Ethernet Net Switch with layer 2, 3 and 4 services

5- Modular chassis basis architecture

6- Layers 2 through 4 hardware-based switch engine (ASIC-based)

7- Hardware based ACLs, router ACLs, VLAN ACLs

8- Protocols: Support for IPv6RIPv1, RIPv2 routing function. support for EIGRP-stub. Hot Standby Router Protocol. IGMP vers 1,2,3.

10- Forwarding bandwidth: Scalable upto 64 Gbps or higher...

11- MAC support up to 32000 MAC or more...

...

Any information, ideas, guidance or link to make the decision easier will be appreciated.

Thank you in advance...

Cheers!

Lad.

Labels:
0 Helpful
6 Replies 6

n.nandrekar
Level 4
Level 4

‎06-10-2008 12:52 AM

Hi!

A Catalyst 6500 can meet all your requirements.

http://www.cisco.com/en/US/prod/collateral/switches/ps5718/ps708/product_at_a_glance0900aecd806a09f2.pdf

Please rrevert if you require any more specific info.

Regards,

Niranjan

l_masoumi
Level 1
Level 1
In response to n.nandrekar

‎06-10-2008 10:36 AM

Hi Niranjan

Thank you for help... I found WS-C6503-E product to be the one I need.. but still not really clear about how many ports and which type of ports this product already has(without adding any module to it). I thought I might need to add a module to 6503 chassis, to be able to have 12 Gigabit Ethernet fiber ports, but not sure if I'm correct?!

I went through the data sheets and tried to understand these things but unsuccessful.

One more, I believe for the rest of my requirement I need to add Supervisor Engine 720 module to this chassis which will occupy 2 slots out of 3 available. Then for having 12 Gigabit Ethernet Fiber ports, if adding a module is the solution, will that one slot be enough?

Thanks again for the help.

Best Regards,

Lad.

0 Helpful

Joseph W. Doherty
Hall of Fame
Hall of Fame

‎06-10-2008 04:30 AM

Besides the 6500, the 4500 series might be suitable, see http://www.cisco.com/en/US/products/hw/switches/ps4324/index.html

0 Helpful

l_masoumi
Level 1
Level 1
In response to Joseph W. Doherty

‎06-10-2008 10:46 AM

Thanks Joseph for help.. I think I better go for Catalyst 6503-E according to the other requirements I have.

0 Helpful

Jagdeep Gambhir
Level 10
Level 10

‎06-10-2008 04:30 AM

Lad,

Go for Cisco Catalyst 6500

http://www.cisco.com/en/US/products/hw/switches/ps708/index.html

Regards,

~JG

l_masoumi
Level 1
Level 1
In response to Jagdeep Gambhir

‎06-10-2008 10:43 AM

Thanks JG for help.. I think you are right.

0 Helpful
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Customers Also Viewed These Support Documents
Review Cisco Networking products for a $25 gift card