06-17-2008 12:22 PM - edited 03-18-2019 09:08 PM
Hello All,
I have configured the hardward conference on CME for AD-Hoc. The conference profile is not able to register with CME. Please see the attached configuration & the error message below.
SCCP Admin State: UP
Gateway IP Address: 10.199.108.1, Port Number: 2000
IP Precedence: 1
User Masked Codec list: None
Call Manager: 10.199.108.1, Port Number: 2000
Priority: N/A, Version: 3.1, Identifier: 1
Transcoding Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 10.199.108.1, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 10
Reported Max Streams: 6, Reported Max OOS Streams: 0
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
Conferencing Oper State: ACTIVE_IN_PROGRESS - Cause Code: NOT_REGIS_WITH_CCM
Active Call Manager: NONE
TCP Link Status: NOT_CONNECTED, Profile Identifier: 2
Reported Max Streams: 32, Reported Max OOS Streams: 0
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
Also, Attached is the debug of sccp details log.
Your help is always appreciated.
Thanks,
Yogesh Mhatre
06-17-2008 02:53 PM
You are missing some command under the telephony-service configuration.
SUMMARY STEPS
1. enable
2. configure terminal
3. telephony-service
4. conference hardware
5. transfer-system full-consult
6. sdspfarm units number
7. sdspfarm tag number device-name
8. sdspfarm conference mute-on mute-on-digits mute-off mute-off-digits
Step 8 you are missing!
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeconf.html
06-17-2008 02:58 PM
And I don't see the global command "dspfarm" to enable the dspfarm. I don't think your dspfarm is running!
06-18-2008 06:56 AM
Hello Chris,
Thanks for your reply.
I tried the dspfarm command & the missing command, still i receive the same message.
Appreciate your help.
Regards,
Yogesh Mhatre
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: