CME Conference Configuration

yogesh.mhatre · ‎06-17-2008

Hello All,

I have configured the hardward conference on CME for AD-Hoc. The conference profile is not able to register with CME. Please see the attached configuration & the error message below.

SCCP Admin State: UP

Gateway IP Address: 10.199.108.1, Port Number: 2000

IP Precedence: 1

User Masked Codec list: None

Call Manager: 10.199.108.1, Port Number: 2000

Priority: N/A, Version: 3.1, Identifier: 1

Transcoding Oper State: ACTIVE - Cause Code: NONE

Active Call Manager: 10.199.108.1, Port Number: 2000

TCP Link Status: CONNECTED, Profile Identifier: 10

Reported Max Streams: 6, Reported Max OOS Streams: 0

Supported Codec: g711ulaw, Maximum Packetization Period: 30

Supported Codec: g711alaw, Maximum Packetization Period: 30

Supported Codec: g729ar8, Maximum Packetization Period: 60

Supported Codec: g729abr8, Maximum Packetization Period: 60

Supported Codec: g729r8, Maximum Packetization Period: 60

Supported Codec: g729br8, Maximum Packetization Period: 60

Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30

Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30

Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30

Conferencing Oper State: ACTIVE_IN_PROGRESS - Cause Code: NOT_REGIS_WITH_CCM

Active Call Manager: NONE

TCP Link Status: NOT_CONNECTED, Profile Identifier: 2

Reported Max Streams: 32, Reported Max OOS Streams: 0

Supported Codec: g711ulaw, Maximum Packetization Period: 30

Supported Codec: g711alaw, Maximum Packetization Period: 30

Supported Codec: g729ar8, Maximum Packetization Period: 60

Supported Codec: g729abr8, Maximum Packetization Period: 60

Supported Codec: g729r8, Maximum Packetization Period: 60

Supported Codec: g729br8, Maximum Packetization Period: 60

Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30

Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30

Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30

Also, Attached is the debug of sccp details log.

Your help is always appreciated.

Thanks,

Yogesh Mhatre

chris.fortner · ‎06-17-2008

You are missing some command under the telephony-service configuration.

SUMMARY STEPS

1. enable

2. configure terminal

3. telephony-service

4. conference hardware

5. transfer-system full-consult

6. sdspfarm units number

7. sdspfarm tag number device-name

8. sdspfarm conference mute-on mute-on-digits mute-off mute-off-digits

Step 8 you are missing!

http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmeconf.html

chris.fortner · ‎06-17-2008

And I don't see the global command "dspfarm" to enable the dspfarm. I don't think your dspfarm is running!

yogesh.mhatre · ‎06-18-2008

Hello Chris,

Thanks for your reply.

I tried the dspfarm command & the missing command, still i receive the same message.

Appreciate your help.

Regards,

Yogesh Mhatre