cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1508
Views
5
Helpful
22
Replies

SRST HELP - what am i doing wrong..?

james.hughes
Level 1
Level 1

Hi All - i'm doing my first deployment of CUCMBE 6.1 with CUPS. Everything running well... except SRST.

The handsets say:

1) x.x.x.x - callmanager 1 ACTIVE

2) x.x.x.x - callmanager 2 SRST

That all looks good.

My router looks like:

call-manager-fallback

secondary-dialtone 0

max-conferences 8 gain -6

transfer-system full-consult

ip source-address 10.37.254.14 port 2000

max-ephones 96

keepalive 10

The source address here is the interface on the ISR router itself. Is that correct?

When i power down the CUCM the phones go blank and not into 'fall back mode'.

All help apperciated!

Thanks - James.

22 Replies 22

Chad Stachowicz
Level 6
Level 6

James,

call-manager-fallback

max-dn 96

This is a required command before things in srst will register.

HTH, please rate helpful posts..

Chad

Thanks Chad

I have the phone now saying "fall back" however, i don't have any buttons etc.. nothing saying 'Redial, New Call etc...'

Naturally, i also can't dial out!

The dialing out is probably due to the dial plan, but any ideas on the soft buttons?

Thanks - JH

Please paste the entire config...

also did you have the gateway registered to CCM before you added max-dn. it needed to register SRST with CCM and srst properly configured and dl the TFTP loads... Else you might get the blank stuff you have. Do you see dn numbers on the phones?

I would...

1.) reload router let it connect to CM and register phones normally.

2.) go into srst verify fnctinoality.

3.) have you configured H323, is this mgcp? then you need to configure h323 fallback!.

Thanks

Chad

Also,

add these under call-manager-fallback

transfer-system full-consult

dialplan-pattern 1 760688.... extension-length 4 <--whatever your did ranges are here

transfer-pattern .T

call-forward pattern .T

Thanks Chad -

GMOSYDISR01#sh run

Building configuration...

Current configuration : 2065 bytes

!

! Last configuration change at 14:04:59 SYD Wed Jun 25 2008 by gmotech

! NVRAM config last updated at 14:05:01 SYD Wed Jun 25 2008 by gmotech

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname GMOSYDISR01

!

boot-start-marker

boot-end-marker

!

card type e1 0 0

enable secret

enable password

!

no aaa new-model

!

resource policy

!

clock timezone SYD 10

network-clock-participate wic 0

!

!

ip cef

!

!

no ip domain lookup

!

!

stcapp ccm-group 1

isdn switch-type primary-net5

!

voice-card 0

no dspfarm

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

username gmotech password 0 l0seme365

!

!

controller E1 0/0/0

pri-group timeslots 1-20 service mgcp

!

controller E1 0/0/1

!

!

!

!

!

!

interface GigabitEthernet0/0

ip address 10.37.254.14 255.255.255.0

duplex auto

speed auto

no mop enabled

!

interface GigabitEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface Serial0/0/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

isdn bind-l3 ccm-manager

no cdp enable

!

ip route 0.0.0.0 0.0.0.0 10.37.254.1

!

!

ip http server

no ip http secure-server

!

!

!

!

!

!

!

control-plane

!

!

!

voice-port 0/0/0:15

!

voice-port 0/1/0

!

voice-port 0/1/1

!

voice-port 0/1/2

!

voice-port 0/1/3

!

voice-port 0/2/0

!

voice-port 0/2/1

!

voice-port 0/2/2

!

voice-port 0/2/3

!

ccm-manager mgcp

ccm-manager config server 10.37.254.10

ccm-manager download-tones

!

mgcp

mgcp call-agent 10.37.254.10 service-type mgcp version 0.1

!

mgcp profile default

!

!

!

dial-peer voice 1 pots

destination-pattern 0....

!

dial-peer voice 10 pots

service mgcpapp

!

!

!

!

!

call-manager-fallback

secondary-dialtone 0

max-conferences 8 gain -6

transfer-system full-consult

ip source-address 10.37.254.14 port 2000

max-ephones 96

max-dn 96

keepalive 10

!

!

line con 0

line aux 0

line vty 0 4

password l0seme365

login local

!

scheduler allocate 20000 1000

ntp clock-period 17180110

ntp server 10.42.10.11

!

end

Can you repost your new full config, now thats it registered to CM again, it should show more mgcp packages ;)

Thanks Chad

I have the phone now saying "fall back" however, i don't have any buttons etc.. nothing saying 'Redial, New Call etc...'

Naturally, i also can't dial out!

The dialing out is probably due to the dial plan, but any ideas on the soft buttons?

Thanks - JH

i would sujest you to make it not gateway srst but CME srst in this case you need to define phones as you are useinf CME then you add buttons, lines DNs for each phone

in this case when your phons fall-back to srst mode will use the configured info

rate if help full

ccm-manager mgcp

ccm-manager config server 10.37.254.10

ccm-manager download-tones

ccm-manager config

ccm-manager fallback-mgcp

application

global

service alternate Default

Add that. Also you need to configure some H323 peers for dialing out.

that will enable h323 fallback. Make sure that your reference is set on the CM device pool.

Thanks,

Chad

also give me

sh ephone reg

sh call-manager-fallback

sh ccm-manager

Thanks,

Chad

add

H323-Services

voice services voip

allow-connection h323 to h323

allow-connection h323 to sip

allow-connection sip to h323

allow-connection sip to sip

dial-peer voice 1050 pots

destination-pattern 91[2-9]..[2-9]......

port 0/0/0:15

forward-digits 11

description *** US / Long Distance ***

add this to enable LD Calling

lastly please register this via mgcp and do ccm-manager when its registered and verify its registered. Then put it into fallback..

Chad

GMOSYDISR01#sh ccm-manager

MGCP Domain Name: GMOSYDISR01

Priority Status Host

============================================================

Primary Registered 10.37.254.10

First Backup None

Second Backup None

Current active Call Manager: 10.37.254.10

Backhaul/Redundant link port: 2428

Failover Interval: 30 seconds

Keepalive Interval: 15 seconds

Last keepalive sent: 15:10:19 SYD Jun 25 2008 (elapsed time: 00:00:05)

Last MGCP traffic time: 15:10:19 SYD Jun 25 2008 (elapsed time: 00:00:05)

Last failover time: None

Last switchback time: None

Switchback mode: Graceful

MGCP Fallback mode: Enabled/OFF

Last MGCP Fallback start time: 15:05:05 SYD Jun 25 2008

Last MGCP Fallback end time: 15:07:07 SYD Jun 25 2008

MGCP Download Tones: Enabled

Custom Tone 1 : Default (United States)

Backhaul Link info:

Link Protocol: TCP

Remote Port Number: 2428

Remote IP Address: 10.37.254.10

Current Link State: OPEN

Statistics:

Packets recvd: 22

Recv failures: 1

Packets xmitted: 24

Xmit failures: 0

PRI Ports being backhauled:

Slot 0, VIC 0, port 0

Configuration Auto-Download Information

=======================================

No configurations downloaded

Current state: Downloading Tone XML file

Configuration Download statistics:

Download Attempted : 3

Download Successful : 3

Download Failed : 0

Configuration Attempted : 1

Configuration Successful : 0

Configuration Failed(Parsing): 0

Configuration Failed(config) : 0

Last config download command:

FAX mode: cisco

Configuration Error History:

GMOSYDISR01#sh ephone

ephone-1 Mac:0021.55D4.C0C4 TCP socket:[3] activeLine:0 UNREGISTERED

mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:12

IP:10.37.11.250 51989 Unknown 435 keepalive 46 max_line 0

ephone-2 Mac:001D.705F.A571 TCP socket:[1] activeLine:0 UNREGISTERED

mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:12

IP:10.37.11.216 49472 Unknown 435 keepalive 50 max_line 0

ephone-3 Mac:0021.5554.A720 TCP socket:[4] activeLine:0 UNREGISTERED

mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:12

IP:10.37.11.240 50034 Unknown 435 keepalive 50 max_line 0

ephone-4 Mac:001D.705E.AE5B TCP socket:[2] activeLine:0 UNREGISTERED

mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:12

IP:10.37.11.222 49665 Unknown 436 keepalive 50 max_line 0

GMOSYDISR01#sh ephone reg

No ephone in specified type/condition.

alright thats registered to CCM. Now add all those commands and put it back into SRST and try dialing out

sh ephone reg

sh call-manager-fallback

sh ccm-manager

You should be able to dial long distance, and hopefully have your buttons

The phones have registered :

ephone-1 Mac:0021.55D4.C0C4 TCP socket:[3] activeLine:0 REGISTERED in SCCP ver 15 and Server in ver 5

mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:12

IP:10.37.11.250 51989 Unknown 435 keepalive 10 max_line 0

ephone-2 Mac:001D.705F.A571 TCP socket:[1] activeLine:0 REGISTERED in SCCP ver 15 and Server in ver 5

mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:12

IP:10.37.11.216 49472 Unknown 435 keepalive 8 max_line 0

ephone-3 Mac:0021.5554.A720 TCP socket:[4] activeLine:0 REGISTERED in SCCP ver 15 and Server in ver 5

mediaActive:0 offhook:0 ringing:0 reset:0 reset_sent:0 paging 0 debug:0 caps:12

IP:10.37.11.240 50034 Unknown 435 keepalive 8 max_line 0

GMOSYDISR01#sh call-manager-fallback

CONFIG (Version=4.0(0))

=====================

Version 4.0(0)

For on-line documentation please see:

www.cisco.com/univercd/cc/td/doc/product/access/ip_ph/ip_ks/index.htm

ip source-address 10.37.254.14 port 2000

max-ephones 96

max-dn 96

max-conferences 8 gain -6

dspfarm units 0

dspfarm transcode sessions 0

huntstop

dialplan-pattern 1 827499... extension-length 3

cnf-file location: system:

cnf-file option: PER-PHONE-TYPE

network-locale[0] US (This is the default network locale for this box)

network-locale[1] US

network-locale[2] US

network-locale[3] US

network-locale[4] US

user-locale[0] US (This is the default user locale for this box)

user-locale[1] US

user-locale[2] US

user-locale[3] US

user-locale[4] US

srst mode auto-provision is OFF

srst ephone template is 0

srst dn template is 0

srst dn line mode is single

time-format 12

date-format mm-dd-yy

timezone 0 Greenwich Standard Time

secondary-dialtone 0

call-forward pattern .T

transfer-pattern .T

keepalive 10

timeout interdigit 10

timeout busy 10

timeout ringing 180

timeout ringin-callerid 8

caller-id name-only: enable

Limit number of DNs per phone:

7910: 36

7935: 36

7936: 36

7940: 36

7960: 36

7970: 36

Log (table parameters):

max-size: 150

retain-timer: 15

transfer-system full-consult

local directory service: enabled.

GMOSYDISR01#sh ccm-manager

MGCP Domain Name: GMOSYDISR01

Priority Status Host

============================================================

Primary Down 10.37.254.10

First Backup None

Second Backup None

Current active Call Manager: None

Backhaul/Redundant link port: 2428

Failover Interval: 30 seconds

Keepalive Interval: 15 seconds

Last keepalive sent: 15:24:49 SYD Jun 25 2008 (elapsed time: 00:03:13)

Last MGCP traffic time: 15:24:34 SYD Jun 25 2008 (elapsed time: 00:03:28)

Last failover time: None

Last switchback time: None

Switchback mode: Graceful

MGCP Fallback mode: Enabled/ON

Last MGCP Fallback start time: 15:25:20 SYD Jun 25 2008

Last MGCP Fallback end time: 15:07:07 SYD Jun 25 2008

MGCP Download Tones: Enabled

Custom Tone 1 : Default (United States)

Backhaul/Redundant link is down

FAX mode: cisco

Configuration Error History:

...

However, my phones are still dead. They just say "CM Fallback serivce operating".

Thanks for your help this far!

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: