Sending different voice calls to two different e1 channels? how?

Answered Question
Jun 25th, 2008
User Badges:

What I want to do is, when I call 1111 I want to send these calls from the first ten channel;

when I want to call 9999 I want it to use the channels from 10 to 30. Does it possible? Two dial peer

sends voice traffics from different e1 channels... How can this be implemented?

thx


Serial0/1/0:0 unassigned YES unset down down

Serial0/1/0:1 unassigned YES unset down down

Serial0/1/0:2 unassigned YES unset down down

Serial0/1/0:3 unassigned YES unset down down

Serial0/1/0:4 unassigned YES unset down down

Serial0/1/0:5 unassigned YES unset down down

Serial0/1/0:6 unassigned YES unset down down

Serial0/1/0:7 unassigned YES unset down down

Serial0/1/0:8 unassigned YES unset down down

Serial0/1/0:9 unassigned YES unset down down

Serial0/1/0:10 unassigned YES unset down down

Serial0/1/0:11 unassigned YES unset down down

Serial0/1/0:12 unassigned YES unset down down

Serial0/1/0:13 unassigned YES unset down down

Serial0/1/0:14 unassigned YES unset down down

Serial0/1/0:15 unassigned YES NVRAM up up

Serial0/1/0:16 unassigned YES unset down down

Serial0/1/0:17 unassigned YES unset down down

Serial0/1/0:18 unassigned YES unset down down

Serial0/1/0:19 unassigned YES unset down down

Serial0/1/0:20 unassigned YES unset down down

Serial0/1/0:21 unassigned YES unset down down

Serial0/1/0:22 unassigned YES unset down down

Serial0/1/0:23 unassigned YES unset down down

Serial0/1/0:24 unassigned YES unset down down

Serial0/1/0:25 unassigned YES unset down down

Serial0/1/0:26 unassigned YES unset down down

Serial0/1/0:27 unassigned YES unset down down

Serial0/1/0:28 unassigned YES unset down down

Serial0/1/0:29 unassigned YES unset down down

Serial0/1/0:30 unassigned YES unset down down

!

controller E1 0/1/0

pri-group timeslots 1-31

!

interface Serial0/1/0:15

no ip address

no ip proxy-arp

isdn switch-type primary-net5

isdn protocol-emulate network

isdn incoming-voice voice

no cdp enable

dial-peer voice 100 pots

destination-pattern 1111

port 0/1/0:15

dial-peer voice 101 pots

destination-pattern 9999

port 0/1/0:15

Correct Answer by Paolo Bevilacqua about 8 years 9 months ago

Trunk-group under controller listing the TS and reference the TG instead of port under DP.


Hope this helps, please rate pos if it does!

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 4 (1 ratings)
Loading.
Paolo Bevilacqua Wed, 06/25/2008 - 06:33
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Before entering the details of how it can be done, can you tell us why do you want to do this and what problem are you trying to solve ?

blackswans Wed, 06/25/2008 - 06:38
User Badges:

The other site wants this to route the calls to outside and inside. He says you must do that for his routing. thx

Paolo Bevilacqua Wed, 06/25/2008 - 06:45
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Can you confirm with them that they need to route based on the channel number rather than called number on a PRI circuit? That is rather unusual in telecom.


However it is possible to configure trunk-group ranging B-channels on a single pri controller.


So I recommend you try to have them do a regular number-based routing before exploring this other route.

blackswans Wed, 06/25/2008 - 06:49
User Badges:

Actually they are giving access levels to these channels thats why they need this. So when I call 1111 it should go from the first ten channel. Do you have any config for that situation ?

thx

Correct Answer
Paolo Bevilacqua Wed, 06/25/2008 - 06:51
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Trunk-group under controller listing the TS and reference the TG instead of port under DP.


Hope this helps, please rate pos if it does!

Actions

This Discussion