06-25-2008 06:31 AM - edited 03-15-2019 11:31 AM
What I want to do is, when I call 1111 I want to send these calls from the first ten channel;
when I want to call 9999 I want it to use the channels from 10 to 30. Does it possible? Two dial peer
sends voice traffics from different e1 channels... How can this be implemented?
thx
Serial0/1/0:0 unassigned YES unset down down
Serial0/1/0:1 unassigned YES unset down down
Serial0/1/0:2 unassigned YES unset down down
Serial0/1/0:3 unassigned YES unset down down
Serial0/1/0:4 unassigned YES unset down down
Serial0/1/0:5 unassigned YES unset down down
Serial0/1/0:6 unassigned YES unset down down
Serial0/1/0:7 unassigned YES unset down down
Serial0/1/0:8 unassigned YES unset down down
Serial0/1/0:9 unassigned YES unset down down
Serial0/1/0:10 unassigned YES unset down down
Serial0/1/0:11 unassigned YES unset down down
Serial0/1/0:12 unassigned YES unset down down
Serial0/1/0:13 unassigned YES unset down down
Serial0/1/0:14 unassigned YES unset down down
Serial0/1/0:15 unassigned YES NVRAM up up
Serial0/1/0:16 unassigned YES unset down down
Serial0/1/0:17 unassigned YES unset down down
Serial0/1/0:18 unassigned YES unset down down
Serial0/1/0:19 unassigned YES unset down down
Serial0/1/0:20 unassigned YES unset down down
Serial0/1/0:21 unassigned YES unset down down
Serial0/1/0:22 unassigned YES unset down down
Serial0/1/0:23 unassigned YES unset down down
Serial0/1/0:24 unassigned YES unset down down
Serial0/1/0:25 unassigned YES unset down down
Serial0/1/0:26 unassigned YES unset down down
Serial0/1/0:27 unassigned YES unset down down
Serial0/1/0:28 unassigned YES unset down down
Serial0/1/0:29 unassigned YES unset down down
Serial0/1/0:30 unassigned YES unset down down
!
controller E1 0/1/0
pri-group timeslots 1-31
!
interface Serial0/1/0:15
no ip address
no ip proxy-arp
isdn switch-type primary-net5
isdn protocol-emulate network
isdn incoming-voice voice
no cdp enable
dial-peer voice 100 pots
destination-pattern 1111
port 0/1/0:15
dial-peer voice 101 pots
destination-pattern 9999
port 0/1/0:15
Solved! Go to Solution.
06-25-2008 06:51 AM
Trunk-group under controller listing the TS and reference the TG instead of port under DP.
Hope this helps, please rate pos if it does!
06-25-2008 06:33 AM
Before entering the details of how it can be done, can you tell us why do you want to do this and what problem are you trying to solve ?
06-25-2008 06:38 AM
The other site wants this to route the calls to outside and inside. He says you must do that for his routing. thx
06-25-2008 06:45 AM
Can you confirm with them that they need to route based on the channel number rather than called number on a PRI circuit? That is rather unusual in telecom.
However it is possible to configure trunk-group ranging B-channels on a single pri controller.
So I recommend you try to have them do a regular number-based routing before exploring this other route.
06-25-2008 06:49 AM
Actually they are giving access levels to these channels thats why they need this. So when I call 1111 it should go from the first ten channel. Do you have any config for that situation ?
thx
06-25-2008 06:51 AM
Trunk-group under controller listing the TS and reference the TG instead of port under DP.
Hope this helps, please rate pos if it does!
06-25-2008 10:12 PM
thx it seems that it works :)
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: