Cisco voicegateway

Unanswered Question
Jun 28th, 2008
User Badges:

I have MD110 as pbx. the MD has E1 link from telco to provide outside calls.

I defined in my VG "9" for going out .

when a user dial 9 two problem occures:

1) the user hears some kind of noises!!

2)the user can not here dial tone


please help


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
paolo bevilacqua Sat, 06/28/2008 - 04:38
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

What exactly is the VG and how is connected to rest of the other things ?


miskoolak Sat, 06/28/2008 - 20:16
User Badges:

The VG is cisco 2821 and is connected via E1 to pbx.

paolo bevilacqua Sun, 06/29/2008 - 08:11
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Hi,


where are you calling with "9" ?

miskoolak Sun, 06/29/2008 - 11:42
User Badges:

hi

here is my config:


dial-peer voice 10 pots

port 0/2/0:15

forward digit all

destination-pattern 9


----------------------


when I dial i can not here PSTN dial-tone from pbx.also the important thing is that when I dial 9 no time slot activation happend

i hear just noise some kind "shshshshsh"

in this point i can dial my number after finishing my dial the connection established.

but i want to hear PSTN dial tone after dialing 9

thank you

paolo bevilacqua Sun, 06/29/2008 - 12:10
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Hi, you are not calling any number because the 9 is absorbed being it pots DP. Add "no strip-digit" and PBX should connect you to PSTN. You can also do a DP like 9.....T this way you can call directly, no need to wait for dialtone.


Please rate post if it helps!

miskoolak Sun, 06/29/2008 - 22:32
User Badges:

Hi again

its mandatory to hear pstn dialtone.

please guide me to hear PSTN dialtone.

waiting for you reply

paolo bevilacqua Sun, 06/29/2008 - 22:34
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

As mentioned before, configure as indicated and you should have dialtone from PSTN.

miskoolak Sun, 06/29/2008 - 23:07
User Badges:

hi

I will do your command and will let you know

miskoolak Tue, 07/01/2008 - 07:48
User Badges:

Dear freind

i provide my your command but still can not hear PSTN dial tone

can you provide me something else?


regards



paolo bevilacqua Tue, 07/01/2008 - 09:00
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

Are you using CM or CME ? Sometime you can configure "secondary dialtone" to emulate PSTN dialtone.

miskoolak Tue, 07/01/2008 - 13:04
User Badges:

there is no any CM or CME on my network

there is just ericcson MD110 and cisco gateway (CISCO 2811)

we are trying to make call from PBX extentions.

but still we can not here PSTN dial tone!

its very importatnt..

if you need further information let me know.

thank you for following up

paolo bevilacqua Tue, 07/01/2008 - 14:27
User Badges:
  • Super Gold, 25000 points or more
  • Hall of Fame,

    Founding Member

The 2821 is connected to both PBX and PSTN ? And to for which purpose ?


Please specify with a diagram all that is connected as requested before.

miskoolak Fri, 07/04/2008 - 23:25
User Badges:

here is diagram


PSTN---PBX1----Router----IP-----Router----PBX2--users


Actions

This Discussion