Dial Peers Doubt

Unanswered Question
Jul 4th, 2008

Hi


My customer have a configuration down. Why the numbers are match on dial-peer 1?


88132734050

82145963269

89256789541


And why the number are match on dial-peer 2?


40822000

35616978

64589696


I think that all the numbers are match in dial-peer 1 because it`s much specific, or because the voice translation, there is a change in choose of dial-peer



voice translation-rule 1

rule 1 /811/ //

rule 2 /800/ //

rule 3 /^812/ /02112/

rule 4 /^813/ /02113/

rule 5 /^814/ /02114/

rule 6 /^815/ /02115/

rule 7 /^816/ /02116/

rule 8 /^817/ /02117/

rule 9 /^818/ /02118/

rule 10 /^819/ /02119/


voice translation-profile local

translation-called 1


e1 0/0/0

trunkgroup 1


e1 0/0/1

trukgroup 1


dial-peer voice 1 pots

trunkgroup 1

destionation-pattern 8[2-9]T

direct-inward-dial

prefix 021


dial-peer voice 2 pots

trunkgroup 1

destination-pattern 8T

direct-inward-dial



  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Kenneth Mohammed Fri, 07/04/2008 - 11:04

Hello,


I believe dial-peers match dialed digits based on longest match..therefore for your first set of numbers, they match dial-peer 1 because the destination pattern 8[2-9]T matchs the first digit "8", and the second digit, which can be any number between 2 and 9, and then the "T", which can be any amount of digits to follow after that. So yes, you are correct in dial-peer 1 is a more specific match for the dialed numbers than dial peer 2.




pgcristovam Fri, 07/04/2008 - 11:08

Yes the 8 is secondary dialtone. So the numbers:


88132734050

82145963269

89256789541



Choosen the dial-peer 1 based on longest? There are any documentation about it? I thinked this numbers choose the dial-peer 2; more specific! The voice translation rule can change the choose of dial-peer?


Jaime Valencia Fri, 07/04/2008 - 11:40

you can issue this command:


show dialplan number

http://www.cisco.com/en/US/docs/ios/12_3/vvf_r/vrg_sh2_ps1839_TSD_Products_Command_Reference_Chapter.html#wp999333


dial-peer hunt command can be used to modify the way the numbers are matched against dial-peers


Dial Peer Configuration on Voice Gateway Routers

http://www.cisco.com/en/US/partner/docs/ios/12_3/vvf_c/dial_peer/dpeer_c.html


HTH


javalenc


if this helps, please rate

Ayodeji Okanlawon Sat, 07/05/2008 - 02:43

your config is missing the translation profile in the dila-p used for outgoing calls.


There are 3 steps to configure voice translation rule...


1. create the voice xlation rule

2. Configure the xlation profile

3. Apply the translation profile to a dail-p and choose the directiont o whihc it should be applied..


hence your config should look like this..


voice translation-rule 1

rule 1 /811/ //

rule 2 /800/ //

rule 3 /^812/ /02112/

rule 4 /^813/ /02113/

rule 5 /^814/ /02114/

rule 6 /^815/ /02115/

rule 7 /^816/ /02116/

rule 8 /^817/ /02117/

rule 9 /^818/ /02118/

rule 10 /^819/ /02119/


voice translation-profile local

translation-called 1


dial-peer voice 1 pots

trunkgroup 1

destionation-pattern 8[2-9]T

direct-inward-dial

traslation-profile outgoing local

prefix 021


dial-peer voice 2 pots

trunkgroup 1

destination-pattern 8T

direct-inward-dial

translation-profile outgoing local


Hence the translation-profile outgoing local

is missing in your config...


In essence no translation is ben used on your config right now, make the changes and see if it gives you what you want


Actions

This Discussion