07-14-2008 01:35 PM - edited 03-15-2019 11:57 AM
I currently have the following scenario, I have two FXO trunk groups on a four port FXO card.
trunk group FXO1
!
!
trunk group FXO2
voice-port 0/1/0
trunk-group FXO1
connection plar 75377
caller-id enable type 2
!
voice-port 0/1/1
trunk-group FXO1
connection plar 75377
caller-id enable type 2
!
voice-port 0/1/2
trunk-group FXO2
connection plar 75378
caller-id enable type 2
!
voice-port 0/1/3
trunk-group FXO2
connection plar 75378
caller-id enable type 2
I have two phones, one phone should use FXO1 and the other phone should use FXO2 for outbound calls.
My outbound Dial-Peers are arranged in the following manner.
dial-peer voice 7 pots
trunkgroup FXO
corlist outgoing css-loc
destination-pattern 9[2-9]......
forward-digits 7
dial-peer voice 72 pots
trunkgroup FXO2
corlist outgoing css-loc
destination-pattern 9[2-9]......
forward-digits 7
dial-peer voice 11 pots
trunkgroup FXO
corlist outgoing css-ld
destination-pattern 91[2-9]..[2-9]......
forward-digits 11
dial-peer voice 112 pots
trunkgroup FXO2
corlist outgoing css-ld
destination-pattern 91[2-9]..[2-9]......
forward-digits 11
dial-peer voice 110 pots
trunkgroup FXO
corlist outgoing css-intl
destination-pattern 9011T
prefix 011
dial-peer voice 1102 pots
trunkgroup FXO2
corlist outgoing css-intl
destination-pattern 9011T
prefix 011
How do I get Ephone 1 to use FXO1 when making outbound calls, and Ephone 2 to use FXO2 when making outbound calls?
ephone 1
no multicast-moh
device-security-mode none
mac-address xxxx.xxxx.xxxx
type 7941
button 1:1
!
ephone 2
no multicast-moh
device-security-mode none
mac-address xxxx.xxxx.xxxx
type 7941
button 1:2
Solved! Go to Solution.
07-14-2008 01:59 PM
H, you use trunk under DN and specialized DPs for that:
dial-peer voice xxx pots
trunkgroup FXO
destination-pattern 81[2-9]......
dial-peer voice xxx pots
trunkgroup FXO2
destination-pattern 82[2-9]......
ephone-dn 1 dual-line
trunk 81
ephone-dn 2 dual-line
trunk 82
Note: since for all calls from DN 1 and 2 will prefix 81 and 82, you need to use that as an the second button and label EXTERNAL.
Note 2: since likey you're not restircitng local calling, don't use corlist on the related DP.
Note 3: There is also a way to do without "trunk". using corlist instead. But, check if the above is satisfying to you first.
07-14-2008 01:59 PM
H, you use trunk under DN and specialized DPs for that:
dial-peer voice xxx pots
trunkgroup FXO
destination-pattern 81[2-9]......
dial-peer voice xxx pots
trunkgroup FXO2
destination-pattern 82[2-9]......
ephone-dn 1 dual-line
trunk 81
ephone-dn 2 dual-line
trunk 82
Note: since for all calls from DN 1 and 2 will prefix 81 and 82, you need to use that as an the second button and label EXTERNAL.
Note 2: since likey you're not restircitng local calling, don't use corlist on the related DP.
Note 3: There is also a way to do without "trunk". using corlist instead. But, check if the above is satisfying to you first.
07-15-2008 04:57 AM
Thank you very much, this worked well in the lab, we are depolying to a multi agent site now.
07-15-2008 05:05 AM
Making customers happy, especially with FXOs, can take some time, fortunately CME has a full bag of tricks to use.
Thanks for the appreciation and good luck!
07-15-2008 05:03 AM
Paolo,
Since the guy was too happy and excited about his problem been resolved he forgot to rate the post, so I helped him. +5 point for you!
07-15-2008 05:08 AM
Deji, I've rated your for the kindness.
07-15-2008 05:14 AM
Thanks Paolo,
I am encouraged!
05-19-2015 09:47 AM
I have four lines, each are directly to the FXO port but I need to use call forwarding on the FXO port to forward to voicemail.
David
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: