L3 Switching Engine WS-F6K-PFC

Unanswered Question
Jul 18th, 2008
User Badges:

Hi,


I have Sup IA, its boots up and comes to console>(enable) mode, i need to configure L3 functionalities, not able to go with session 15, pls let me know how to configure the same.


Pls look into the below configuration.



sh module


Mod Slot Ports Module-Type Model Sub Status

--- ---- ----- ------------------------- ------------------- --- --------

1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok

2 2 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes standby

3 3 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok

4 4 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok

5 5 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok

6 6 48 10/100BaseTX Ethernet WS-X6248-RJ-45 no ok

7 7 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok

8 8 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok

9 9 48 10/100BaseTX Ethernet WS-X6348-RJ-45 yes ok


Mod Module-Name Serial-Num

--- -------------------- -----------

1 SAD042303TF

2 SAD042303HZ

3 SAD041905TV

4 SAL08239KDK

5 SAD041905LJ

6 SAD041905PW

7 SAL062517N2

8 SAL062720C0

9 SAL063242GR

--More--

Mod MAC-Address(es) Hw Fw Sw

--- -------------------------------------- ------ ---------- -----------------

1 00-b0-8e-83-7e-a6 to 00-b0-8e-83-7e-a7 3.1 5.3(1) 7.6(3a)

00-b0-8e-83-7e-a4 to 00-b0-8e-83-7e-a5

00-0b-45-95-cc-00 to 00-0b-45-95-cf-ff

2 00-b0-c2-f5-a7-82 to 00-b0-c2-f5-a7-83 3.1 5.3(1) 7.6(3a)

00-b0-c2-f5-a7-80 to 00-b0-c2-f5-a7-81

3 00-01-97-15-b6-80 to 00-01-97-15-b6-af 1.2 5.1(1)CSX 7.6(3a)

4 00-11-21-b1-c3-e0 to 00-11-21-b1-c4-0f 8.1 5.4(2) 7.6(3a)

5 00-01-97-15-f6-a0 to 00-01-97-15-f6-cf 1.2 5.1(1)CSX 7.6(3a)

6 00-01-97-0e-38-d0 to 00-01-97-0e-38-ff 1.2 5.1(1)CSX 7.6(3a)

7 00-09-b7-93-98-54 to 00-09-b7-93-98-83 6.1 5.4(2) 7.6(3a)

8 00-09-b7-93-b5-d0 to 00-09-b7-93-b5-ff 6.1 5.4(2) 7.6(3a)

9 00-09-b7-93-b6-00 to 00-09-b7-93-b6-2f 6.1 5.4(2) 7.6(3a)


Mod Sub-Type Sub-Model Sub-Serial Sub-Hw Sub-Sw

--- ----------------------- ------------------- ----------- ------ ------

1 L3 Switching Engine WS-F6K-PFC SAD04230AJN 1.1

2 L3 Switching Engine WS-F6K-PFC SAD04230ABJ 1.1

4 Inline Power Module WS-F6K-VPWR 2.0 1.0

7 Inline Power Module WS-F6K-VPWR 1.0 1.0

8 Inline Power Module WS-F6K-VPWR 1.0 1.0

--More-- 9 Inline Power Module WS-F6K-VPWR 1.0 1.0






Attachment: 
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Jerry Ye Sat, 07/19/2008 - 20:09
User Badges:
  • Cisco Employee,

There aren't any MSFC's daughter card install in your switch:


#module 15 empty

!

#module 16 empty


MSFC's will show up in your "show module" command as module 15 or 16, depend on which line card.


HTH,

jerry

saravanababu22 Sat, 07/19/2008 - 21:54
User Badges:

jerry,


you are right, but there is PFC card, in sh module status, you can see L3 Switching Engine, where we have a similar switch being used for L3. also this switch was earlier used as distribution switch, still working on it.

will share if done.


regards

Sara

Actions

This Discussion