Match unknown number with analoge FXO interface

Unanswered Question
Jul 27th, 2008
User Badges:

Hi There,


I tried to make a incoming dial-peer what matches a unknown number with my callmanager express router.


I have an FXO interface and this one is connected to a analoge provider line,however its not sending its own number over the line so i cannot match with the incoming dail-peer..


Does anyone have a solution for this?


Can i match every number that is coming inside..?


Thanks

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Marwan ALshawi Sun, 07/27/2008 - 22:12
User Badges:
  • Purple, 4500 points or more
  • Community Spotlight Award,

    Best Publication, December 2015

try the following command in your incoming dial-peer


incoming called-number .


dont forget the dot

this will make what is called defaul- incomeing dial-peer

good luck


Rate,if helpful

kennis1977 Mon, 07/28/2008 - 06:22
User Badges:

ah ok..going to tried that...


and can i use this dot also for my translation-profile ?


because my phonenumber is 100

and how does it look like then (the translation-profile?)


Thanks

Marwan ALshawi Mon, 07/28/2008 - 17:59
User Badges:
  • Purple, 4500 points or more
  • Community Spotlight Award,

    Best Publication, December 2015

what you wanna achive with the translation profile?


and what numbers you have ?


post the details to let me help you ok

kennis1977 Mon, 07/28/2008 - 23:47
User Badges:

Hi,


I have an analoge line with number 0101234567

for example..


however this number is ending at 567 and my number internal is 100


so if we can match with the dot its not letting number 100 to ring


So thats wy i think we also need a translation-profile that is pointing the dot to 100


But..perhaps can you also give me the complete incoming dial-peer that would be great!


so the only thing i want to do is let the phone ring when someone is calling the external number.


hope you can help me..


Gr


Marwan ALshawi Tue, 07/29/2008 - 03:48
User Badges:
  • Purple, 4500 points or more
  • Community Spotlight Award,

    Best Publication, December 2015

the following config will take any number coming the port such as 0/0/1 ISDN and change the called number to 100

so if u have a dial-peer for a number 100

such as pots for analog phon or voip

the call will be forwarded to that dial-peer


Voice translation-rule 1

Rule 1 /.*/ /100/


Voice translation-profile profile1

Translated called 1


Dial-peer voice 9 pots

Incoming called-number .

direct-inward-dial

translation-profile incoming profile1

port 0/0/1

forward-digits all



but if you have FXO ( which your case FXO i think)

just put the following command under the FXO port

and it will forward the call to the number 100


voice-port 1/0/0

connection plar opx 100


PSTN calls arriving on the FXO port can now terminate on extension 100

(replace the port 1/0/0 with your own port )


any try it and let me know

Marwan ALshawi Tue, 07/29/2008 - 05:48
User Badges:
  • Purple, 4500 points or more
  • Community Spotlight Award,

    Best Publication, December 2015

focus on this one:


just put the following command under the FXO port

and it will forward the call to the number 100


voice-port 1/0/0

connection plar opx 100


PSTN calls arriving on the FXO port can now terminate on extension 100

(replace the port 1/0/0 with your own port )


dont forget to make pots dial-peer for ur analog phone such as

dial-peer voice 3 pots

destination-pattren 100

port 1/0/1


where the port is ur FXS analog phone port


let me know if its worked or not


kennis1977 Tue, 07/29/2008 - 07:09
User Badges:

Great!!!


The last config worked..


with the plax connection...


the dial-peer incoming didn't worked..


so this is then very easy with only one command...

however normally the dial-peer must work but then we need a number to match...but tis is great... thank you...

Marwan ALshawi Tue, 07/29/2008 - 07:12
User Badges:
  • Purple, 4500 points or more
  • Community Spotlight Award,

    Best Publication, December 2015

i confused first time

with FXO only the command i have given you work

but if u have trunk or an ISDN link then the incoming dial-peer condig should be use


any way i am glad its working

please Rate the helpful post

and good luck

kennis1977 Tue, 07/29/2008 - 07:14
User Badges:

Yep...great..


thank you for your help..


and i rate you reply...


Thanks



Actions

This Discussion