Buy or Renew
Buy or Renew
Cisco + Splunk: It’s a new day for your data. Learn more.
 
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation
391
Views
5
Helpful
2
Replies

system logs.

ilnaiduccna
Level 1
Level 1

‎08-10-2008 03:23 PM - edited ‎03-06-2019 12:42 AM

Hi Experts,

I just found the below log messages from one of my 3560s but I couldn't identify the time format like what. When typing #sh clock its showing normal format.

What and how would be the time format config.

Can anybody please suggest on this.

3w2d: %LINK-3-UPDOWN: Interface FastEthernet0/10, changed state to down

3w2d: %LINK-3-UPDOWN: Interface FastEthernet0/10, changed state to up

3w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to up

3w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to down

3w2d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to up

3w3d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to down

3w3d: %LINK-3-UPDOWN: Interface FastEthernet0/10, changed state to down

3w3d: %LINK-3-UPDOWN: Interface FastEthernet0/10, changed state to up

3w3d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to up

3w3d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to down

3w3d: %LINK-3-UPDOWN: Interface FastEthernet0/10, changed state to down

3w3d: %LINK-3-UPDOWN: Interface FastEthernet0/10, changed state to up

3w3d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to up

3w3d: %ILPOWER-7-DETECT: Interface Fa0/10: Power Device detected: IEEE PD

3w3d: %ILPOWER-5-POWER_GRANTED: Interface Fa0/10: Power granted

3w3d: %ILPOWER-5-IEEE_DISCONNECT: Interface Fa0/10: PD removed

3w3d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to down

3w3d: %LINK-3-UPDOWN: Interface FastEthernet0/10, changed state to down

3w3d: %LINK-3-UPDOWN: Interface FastEthernet0/10, changed state to up

3w3d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to up

3w3d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to down

3w3d: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/10, changed state to up

3w4d: %CLEAR-5-COUNTERS: Clear counter on all interfaces by initial on vty0 (206.116.76.140)

Switch#sh clock

19:17:25.540 EST Sun Aug 10 2008

Regards,

Naidu :-)

Labels:
0 Helpful
2 Replies 2

Mark Yeates
Level 7
Level 7

‎08-10-2008 03:32 PM

Naidu,

You should set your logging to the date instead of uptime. Here is the command to set your logging to the local time to the switch.

config t

service timestamps log datetime msec localtime show-timezone

HTH,

Mark

ilnaiduccna
Level 1
Level 1
In response to Mark Yeates

‎08-10-2008 04:06 PM

Hi Mark,

Thanks for the help.

I got understand and will implement it.

Regards,

Naidu.

0 Helpful
Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Customers Also Viewed These Support Documents
Review Cisco Networking products for a $25 gift card