exit interface failed

Answered Question

Hello, I am trying to set up charter cable on a 1811 router. I am using SDM to set it up, and the FE1 interface is set as DHCP. When testing the interface, I'm getting an error message <exit interface failed> and the recommended action <Select 'User-specified' option or add a 'host specific/network specific/default' route through this interface and retest connection.>

Here is the configuration file

!This is the running config of the router: 192.168.1.1

!----------------------------------------------------------------------------

!version 12.3

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname XXXXXX

!

boot-start-marker

boot-end-marker

!

no logging buffered

enable secret 5 XXXXXXXXXXXXX

enable password XXXXXXX

!

username XXXXXXXXX privilege 15 secret 5 XXXXXXXXXXXXXXXX.

mmi polling-interval 60

no mmi auto-configure

no mmi pvc

mmi snmp-timeout 180

dot11 network-map

no aaa new-model

ip subnet-zero

no ip routing

!

!

no ip cef

ip dhcp excluded-address 192.168.1.1 192.168.1.99

!

ip dhcp pool sdm-pool1

import all

network 192.168.1.0 255.255.255.0

default-router 192.168.1.1

lease infinite

!

!

ip ips po max-events 100

no ftp-server write-enable

!

!

!

!

!

bridge irb

!

!

interface Dot11Radio0

no ip address

no ip route-cache

!

ssid CISCO ROUTER

authentication open

guest-mode

!

speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0

bridge-group 2

bridge-group 2 subscriber-loop-control

bridge-group 2 spanning-disabled

bridge-group 2 block-unknown-source

no bridge-group 2 source-learning

no bridge-group 2 unicast-flooding

!

interface Dot11Radio1

no ip address

no ip route-cache

shutdown

!

ssid CISCO ROUTER

authentication open

guest-mode

!

speed basic-6.0 9.0 basic-12.0 18.0 basic-24.0 36.0 48.0 54.0

station-role root

bridge-group 2

bridge-group 2 subscriber-loop-control

bridge-group 2 spanning-disabled

bridge-group 2 block-unknown-source

no bridge-group 2 source-learning

no bridge-group 2 unicast-flooding

!

interface FastEthernet0

description $ETH-WAN$

ip address dhcp client-id FastEthernet0

no ip route-cache

speed auto

half-duplex

!

interface FastEthernet1

description $ETH-WAN$

ip address dhcp client-id FastEthernet1

ip nat outside

ip virtual-reassembly

no ip route-cache

duplex auto

speed auto

!

interface FastEthernet2

no ip address

!

interface FastEthernet3

no ip address

!

interface FastEthernet4

no ip address

!

interface FastEthernet5

no ip address

!

interface FastEthernet6

no ip address

!

interface FastEthernet7

no ip address

!

interface FastEthernet8

no ip address

!

interface FastEthernet9

no ip address

!

interface Vlan1

no ip address

no ip route-cache

bridge-group 2

!

interface Async1

no ip address

no ip route-cache

!

interface BVI2

ip address 192.168.1.1 255.255.255.0

ip nat inside

ip virtual-reassembly

no ip route-cache

!

ip classless

!

!

ip http server

ip http authentication local

ip http secure-server

ip nat inside source list 1 interface FastEthernet1 overload

!

access-list 1 remark INSIDE_IF=BVI2

access-list 1 remark SDM_ACL Category=2

access-list 1 permit 192.168.1.0 0.0.0.255

dialer-list 1 protocol ip permit

!

!

!

!

control-plane

!

bridge 2 protocol ieee

bridge 2 route ip

!

line con 0

line 1

stopbits 1

speed 115200

flowcontrol hardware

line aux 0

line vty 0 4

privilege level 15

password XXXXXX

login local

transport input telnet ssh

!

end

Any ideas what my be the problem? thanks

I have this problem too.
0 votes
Correct Answer by Mark Yeates about 8 years 3 months ago

Roger,

Try consoling into the router and add the "ip routing" command, Then give it another try.

HTH,

Mark

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.

Actions

This Discussion