08-28-2008 12:49 AM
Hi everybody,
I have a 3725 with NM-30DM and I'd like to replace it with a 2811 with PDVM2-36DM.
Here you find the 3725 configuration and the new configuration I put in 2811:
3725:
!
card type e1 2
!
modem country mica italy
!
virtual-profile virtual-template 1
isdn switch-type primary-net5
!
controller E1 2/0
pri-group timeslots 1-31
!
interface FastEthernet0/0
ip address 172.17.9.3 255.255.255.240
speed 100
full-duplex
!
interface Serial2/0:15
no ip address
encapsulation ppp
dialer idle-timeout 600
dialer load-threshold 5 outbound
isdn switch-type primary-net5
isdn incoming-voice modem
ppp authentication chap
ppp multilink
ppp multilink load-threshold 5 outbound
!
interface Virtual-Template1
ip unnumbered FastEthernet0/0
peer default ip address pool dialup
ppp authentication chap
ppp multilink
ppp multilink load-threshold 5 outbound
!
interface Group-Async0
description Interface Async Dial-In
ip unnumbered FastEthernet0/0
encapsulation ppp
ip tcp header-compression
dialer in-band
dialer idle-timeout 600
async mode dedicated
peer default ip address pool dialup
ppp authentication pap chap
ppp multilink
group-range 33 62
!
ip local pool dialup 172.17.9.129 172.17.9.254
!
dial-peer cor custom
!
line 33 62
session-timeout 600
script reset cisco
modem Dialin
modem autoconfigure discovery
autocommand ppp
transport preferred none
transport input all
transport output none
autoselect during-login
autoselect ppp
!
2811:
!
card type e1 1
!
modem firmware slot 0 location flash:V3_07.axf
modem country v12 e1-default
!
virtual-profile virtual-template 1
multilink bundle-name authenticated
isdn switch-type primary-net5
!
controller E1 1/0
pri-group timeslots 1-31
!
interface FastEthernet0/0
ip address 172.17.9.4 255.255.255.240
duplex full
speed 100
!
interface Serial1/0:15
description *** ISDN PRI BT Italia ***
no ip address
encapsulation ppp
dialer idle-timeout 600
dialer load-threshold 5 outbound
isdn switch-type primary-net5
isdn incoming-voice modem
ppp authentication chap
ppp multilink
ppp multilink load-threshold 5 outbound
!
interface Virtual-Template1
ip unnumbered FastEthernet0/0
peer default ip address pool dialup
ppp authentication chap
ppp multilink
ppp multilink load-threshold 5 outbound
!
interface Group-Async0
description Interface Async Dial-In
ip unnumbered FastEthernet0/0
encapsulation ppp
ip tcp header-compression
dialer in-band
dialer idle-timeout 600
async mode dedicated
peer default ip address pool dialup
ppp authentication pap chap
ppp multilink
group-range 0/322 0/357
!
ip local pool dialup 172.17.9.129 172.17.9.254
!
line 0/322 0/357
session-timeout 600
modem InOut
modem autoconfigure discovery
autocommand ppp
transport preferred none
transport input all
transport output none
autoselect during-login
autoselect ppp
!
With this configuration the 2811 is unable to receive incoming calls. I tried also to use 'modem country v12 italy' but it didn't work.
What's wrong with the new configuration?
Many thanks
Regards
Stefano
Solved! Go to Solution.
08-28-2008 04:04 PM
Please try adding the network-clock participate and select command as appropriate for your setup:
Example - NOTE: you will need to add E1 instead of T1
network-clock-participate slot 1
network-clock-select 1 T1 1/0
network-clock-select 2 T1 1/1
Thanks, Mak
08-28-2008 04:04 PM
Please try adding the network-clock participate and select command as appropriate for your setup:
Example - NOTE: you will need to add E1 instead of T1
network-clock-participate slot 1
network-clock-select 1 T1 1/0
network-clock-select 2 T1 1/1
Thanks, Mak
08-29-2008 12:16 AM
It works!!
Thank you so much!
Stefano
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: