09-01-2008 07:25 AM - edited 03-06-2019 01:06 AM
HI
I am trying to run Layer3 with LACP Port-channels from C6k--L3(lacp)--JuniperEX4200 running ospf. It comes up in EXSTART state so deb ip osp adj and see Juniper sending mtu of 1482. Since 1482 is not support on Cisco, I hard-code mtu on both Cisco and Juniper to 1500 but no good so tried on cisco interface "ip opsf mtu-ignore" and still no good. If I take out port-channel and use a normal Layer 3 physical interface or just use L2 port-channel or L2 trunks, it works but I rather have it working with L3 LACP. For simplicity, I only use one physicaly interface for the port-channels right now.
Aug 28 16:19:46.430: OSPF: Send DBD to 10.0.38.6 on Port-channel98 seq 0xE6E opt 0x42 flag 0x7 len 32
Aug 28 16:19:46.430: OSPF: Retransmitting DBD to 10.0.38.6 on Port-channel98 [7]
Aug 28 16:19:47.270: OSPF: Rcv DBD from 10.0.38.6 on Port-channel98 seq 0xA0873C6 opt 0x42 flag 0x7 len 32 mtu 1486 state EXSTART
Aug 28 16:19:47.270: OSPF: First DBD and we are not SLAVE
I ABOVE REPEATS ITSELF FOR MULTIPLE TIMES AND THEN BELOW BUT WILL EVENTUALLY RESTART TRYING TO NEIGHBOR UP and GO THROUGH THE WHOLE CYCLE AGAIN:
Aug 28 16:21:21.431: OSPF: Killing nbr 10.0.38.6 on Port-channel98 due to excessive (25) retransmissions
Aug 28 16:21:21.431: OSPF: 10.0.38.6 address 192.168.98.1 on Port-channel98 is dead, state DOWN
Aug 28 16:21:21.431: %OSPF-5-ADJCHG: Process 1, Nbr 10.0.38.6 on Port-channel98 from EXSTART to DOWN, Neighbor Down: Too many retransmissions
Cisco's config:
interface Port-channel98
description TO-JUNIPER-LAYER3-SWITCH-TEST
ip address 192.168.98.2 255.255.255.252
logging event spanning-tree status
logging event bundle-status
logging event trunk-status
load-interval 30
interface GigabitEthernet1/35
description TO-JUNIPER-LAYER3-SWITCH-TEST
no ip address
logging event link-status
logging event spanning-tree status
logging event bundle-status
logging event trunk-status
load-interval 30
carrier-delay msec 0
channel-group 98 mode active
router ospf 1
log-adjacency-changes
passive-interface default
no passive-interface Vlan2
no passive-interface GigabitEthernet1/35
no passive-interface Port-channel98
network 10.0.0.0 0.0.255.255 area 0
network 10.1.0.0 0.0.255.255 area 0
network 192.168.98.0 0.0.0.3 area 98
Relevant Juniper configs:
ge-0/0/46 {
ether-options {
802.3ad ae2;
ae2 {
mtu 1500;
aggregated-ether-options {
lacp {
passive;
}
}
unit 0 {
family inet {
address 192.168.98.1/30;
protocols {
ospf {
area 0.0.0.98 {
area-range 10.0.98.0/23;
interface ae2.0;
interface ge-0/0/46.0;
09-01-2008 10:17 AM
Hello Tony,
I would try to use
int po98
ip mtu 1482
to see if MTU mismatch can be solved
Hope to help
Giuseppe
09-01-2008 07:06 PM
As I noted in my post, I already did this and it is not supported.
Thx
09-01-2008 10:18 PM
Hello Tony,
I thought you had tried to use mtu 1482 inside port-channel so I was thinking of ip mtu 1482.
Best Regards
Giuseppe
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: