09-02-2008 09:34 AM - edited 03-15-2019 12:59 PM
All,
I have a CME site in mexico that has a generic dial-peer set up to route 9T calls out the telco line.
What is the best way to set this up?
How do you place a call outbound from this site, non-VoIP call?
I do not know how to dial the US from a Mexico phone.
voice translation-rule 2500
rule 1 /2500/ /1001/
rule 2 /2501/ /1001/
rule 3 /2502/ /1001/
rule 4 /2503/ /1001/
rule 5 /2504/ /1001/
rule 6 /2505/ /1001/
rule 7 /2506/ /1001/
rule 8 /2507/ /1001/
rule 9 /2508/ /1001/
rule 10 /2509/ /1001/
rule 12 /2510/ /1001/
!
!
voice translation-profile MAIN
translate called 2500
!
controller E1 0/0/1
framing NO-CRC4
ds0-group 1 timeslots 1-10 type r2-digital r2-compelled ani
cas-custom 1
country telmex use-defaults
category 2
answer-signal group-b 1
!
voice-port 0/0/1:1
!
dial-peer voice 2 pots
destination-pattern 9T
port 0/0/1:1
forward-digits all
Thanks,
Rick
Solved! Go to Solution.
09-02-2008 09:46 AM
Your generic dial-peer forwards all digits inculding the 9, the quickest solution would be to remove the "forward-digits all" command, but I would recommand making more explicit dial-peers as this one will always introduce inter-digit timouts. Create one for Local, LD, International and emergency dialing.
Chris
09-02-2008 10:19 AM
00 - international direct dialing (00 + country code + nat'l number) including USA and Canada.
01 - domestic direct dialing (01 + area code + number)
02 - domestic operator dialing (02 + area code + number)
09 - international operator dialing (09 + country code + number) including USA and Canada.
Chris
09-02-2008 09:46 AM
Your generic dial-peer forwards all digits inculding the 9, the quickest solution would be to remove the "forward-digits all" command, but I would recommand making more explicit dial-peers as this one will always introduce inter-digit timouts. Create one for Local, LD, International and emergency dialing.
Chris
09-02-2008 09:53 AM
I plan on doing that, but wanted something to test with first.
How do I strip the 9 so just the actual number outpulses?
Do I just remove the foward digits command?
Everything else look ok?
09-02-2008 09:54 AM
I plan on doing that, but wanted something to test with first.
How do I strip the 9 so just the actual number outpulses?
Do I just remove the foward digits command?
Everything else look ok?
09-02-2008 09:54 AM
I plan on doing that, but wanted something to test with first.
How do I strip the 9 so just the actual number outpulses?
Do I just remove the foward digits command?
Everything else look ok?
09-02-2008 09:57 AM
Yes, pots dial-peers automatically strip explicitely matched digits, so in your case since 9 is explicitely matched it will not be forwarded.
HTH,
Chris
09-02-2008 09:59 AM
awesome this is what I thought but still new to all of this. more familiar with CUCM 6.1
Now about dialing out in Mexico, how do you make a stateside call?
is it the same as done here in the US, 1-
09-02-2008 10:14 AM
I believe it is 001-NPA-NXX-xxxx
09-02-2008 10:19 AM
00 - international direct dialing (00 + country code + nat'l number) including USA and Canada.
01 - domestic direct dialing (01 + area code + number)
02 - domestic operator dialing (02 + area code + number)
09 - international operator dialing (09 + country code + number) including USA and Canada.
Chris
09-02-2008 12:10 PM
Thanks Chris.
I found a lovely little cisco feature that when you do no forward-digits all
it likes to make that statement forward-digits 0
I had to remove the whole dial-peer and reapply the config without the forward statements.
Thanks for everything!
Also, CDW, where you based out of? we are using them a lot for our IPCC and now getting Voice Advantage for a lot of issues I cannot either get to or resolve myself, we have been getting support from Southfield, MI
09-02-2008 12:29 PM
I am out of Chicago office, hopefully we are treating you well :-)
Chris
09-02-2008 09:54 AM
I plan on doing that, but wanted something to test with first.
How do I strip the 9 so just the actual number outpulses?
Do I just remove the foward digits command?
Everything else look ok?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: