Virtual switch 6509

Unanswered Question
Sep 10th, 2008

When I converted my switchs(6509E) to virtual mode , my service modules were powered down, I tried to use command " power enable " but not active. Pls tell me how turn on

Regards

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
funyphong Wed, 09/10/2008 - 21:59

CORE1#show version

Cisco IOS Software, s72033_rp Software (s72033_rp-ADVIPSERVICESK9_WAN-VM), Versi on 12.2(33)SXH1, RELEASE SOFTWARE (fc3)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2008 by Cisco Systems, Inc.

Compiled Thu 17-Jan-08 08:09 by prod_rel_team

Calin Chiorean Wed, 09/10/2008 - 23:33

Hi!

You are using a VSS there? Do a show module and paste here the results.

In case you are using VSS,

do the following:

sh platform hardware pfc mode

PFC operating mode : (tell us what is displayed here)

If modules are installed in a system that contains a DFC3C, then the module may never be allowed to power up.

Cheers,

Calin

funyphong Thu, 09/11/2008 - 00:14

CORE1#show module

Mod Ports Card Type

Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1213KKAY

2 6 Firewall Module WS-SVC-FWM-1 SAD121204LJ

3 1 Application Control Engine Module ACE20-MOD-K9 SAD1212020S

4 8 Intrusion Detection System WS-SVC-IDSM-2 SAD120907H9

5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1213K85Z

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 001f.9e3d.d800 to 001f.9e3d.d82f 2.7 12.2(14r)S5 12.2(33)SXH1 Ok

2 001f.6c89.112a to 001f.6c89.1131 4.2 Unknown Unknown PwrDown

3 001f.9e1a.e9b8 to 001f.9e1a.e9bf 2.3 Unknown Unknown PwrDown

4 001f.9e1a.c238 to 001f.9e1a.c23f 6.3 Unknown Unknown PwrDown

5 001e.7a58.5f40 to 001e.7a58.5f47 2.0 8.5(2) 12.2(33)SXH1 Ok

CORE1#show platform hardware pfc mode

PFC operating mode : PFC3C

Configured PFC operating mode : None

funyphong Thu, 09/11/2008 - 00:26

CORE1#show module

Mod Ports Card Type

Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 48 CEF720 48 port 10/100/1000mb Ethernet WS-X6748-GE-TX SAL1213KKAY

2 6 Firewall Module WS-SVC-FWM-1 SAD121204LJ

3 1 Application Control Engine Module ACE20-MOD-K9 SAD1212020S

4 8 Intrusion Detection System WS-SVC-IDSM-2 SAD120907H9

5 5 Supervisor Engine 720 10GE (Active) VS-S720-10G SAL1213K85Z

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 001f.9e3d.d800 to 001f.9e3d.d82f 2.7 12.2(14r)S5 12.2(33)SXH1 Ok

2 001f.6c89.112a to 001f.6c89.1131 4.2 Unknown Unknown PwrDown

3 001f.9e1a.e9b8 to 001f.9e1a.e9bf 2.3 Unknown Unknown PwrDown

4 001f.9e1a.c238 to 001f.9e1a.c23f 6.3 Unknown Unknown PwrDown

5 001e.7a58.5f40 to 001e.7a58.5f47 2.0 8.5(2) 12.2(33)SXH1 Ok

CORE1#show platform hardware pfc mode

PFC operating mode : PFC3C

Configured PFC operating mode : None

plgingembre Sat, 09/13/2008 - 14:20

Hi,

Here is what you were asking :

rtr-sem-dc#sh platform hardware pfc mode

PFC operating mode : PFC3C

Configured PFC operating mode : None

rtr-sem-dc#

Kind Regards,

--

Pierre-Louis

Ryan Carretta Sun, 09/14/2008 - 00:20

Hi,

Your question was already answered in this thread:

The service modules you have aren't supported with VSS quite yet. VSS support for ACE10, ACE20, FWSM, IDSM, and WiSM will come with the 12.2(33)SXI code release.

-Ryan

Actions

This Discussion