cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
911
Views
0
Helpful
5
Replies

Problem with Cisco 1841 Router

gagarwal4
Level 1
Level 1

Hi,

I am facing problem with my cisco 1841 router and it is not giving me console accese. Please find router logs as below -

Readonly ROMMON initialized

program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0xcb80

program load complete, entry point: 0x8000f000, size: 0xd4a9a0

Self decompressing the image : #################################################

################################################################################

######## [OK]

Smart Init is enabled

smart init is sizing iomem

ID MEMORY_REQ TYPE

0X003AA110 public buffer pools

0X00211000 public particle pools

0X000021B8 Onboard USB

If any of the above Memory Requirements are

"UNKNOWN", you may be using an unsupported

configuration or there is a software problem and

system operation may be compromised.

Allocating additional 7713952 bytes to IO Memory.

PMem allocated: 117440512 bytes; IOMem allocated: 16777216 bytes

Restricted Rights Legend

Use, duplication, or disclosure by the Government is

subject to restrictions as set forth in subparagraph

(c) of the Commercial Computer Software - Restricted

Rights clause at FAR sec. 52.227-19 and subparagraph

(c) (1) (ii) of the Rights in Technical Data and Computer

Software clause at DFARS sec. 252.227-7013.

cisco Systems, Inc.

170 West Tasman Drive

San Jose, California 95134-1706

Cisco IOS Software, 1841 Software (C1841-IPBASE-M), Version 12.4(1c), RELEASE SO

FTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2005 by Cisco Systems, Inc.

Compiled Tue 25-Oct-05 17:10 by evmiller

Image text-base: 0x6007ECA0, data-base: 0x61480000

Port Statistics for unclassified packets is not turned on.

Cisco 1841 (revision 7.0) with 114688K/16384K bytes of memory.

Processor board ID FHK122222J7

2 FastEthernet interfaces

DRAM configuration is 64 bits wide with parity disabled.

191K bytes of NVRAM.

31360K bytes of ATA CompactFlash (Read/Write)

username cisco privilege 15 one-time secret 0 cisco

^

% Invalid input detected at '^' marker.

ip http secure-server

^

% Invalid input detected at '^' marker.

transport input telnet ssh

^

% Invalid input detected at '^' marker.

1 Accepted Solution

Accepted Solutions

It looks like you may need to do a password recovery on the router. I see from the output that it did not accept the username in the config. It also looks like you went from a crypto IOS to a non crypto IOS. Here are instructions on how to run a password recovery.

http://www.cisco.com/en/US/products/hw/routers/ps259/products_password_recovery09186a0080094675.shtml

HTH,

Mark

View solution in original post

5 Replies 5

satish_zanjurne
Level 4
Level 4

Are you getting the telnet access ??

no.. infact i am not able to access it through console

no.. i don't get console access also

It looks like you may need to do a password recovery on the router. I see from the output that it did not accept the username in the config. It also looks like you went from a crypto IOS to a non crypto IOS. Here are instructions on how to run a password recovery.

http://www.cisco.com/en/US/products/hw/routers/ps259/products_password_recovery09186a0080094675.shtml

HTH,

Mark

Hi Mate ,

what if i have password recovery mechanism disabled.. in that case what the next option...

thanks

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: