command to show details including int description

Unanswered Question
Sep 25th, 2008

I used to know a command that would display alot of information about the interfaces on teh switch. It was similar to "sho int des" but it had more fields in it than just the description. It was like a combination of "sh ip int brie" and "sho int des".

I cannot remember this command and have looked thru the context on the switch but to no avail.

Hopefully one of you will know exactly what I am referencing here.

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
singhsaju Thu, 09/25/2008 - 12:20

Hello,

Are you looking for "show interface status" on IOS switches and "show port status" on CATOS.

HTH

Saju

Pls rate helpful posts

Kevin Melton Fri, 09/26/2008 - 06:08

this is in reference to IOS vs. CatOS. I tried your command "sho int status" but that is not the command I was referencing.

The command I was referencing showed the description, and then several other columns of data with respect to each interface in each row.

I had referenced this command from training somewhere, but cannot at this point remember what it was. I was using it last summer.

I think the command is four words in length.

Thanks

Kevin

Prashanth Krishnappa Fri, 09/26/2008 - 06:15

Was it show interfaces summary? It would help if you remember what fields you saw

7606#sh interfaces summary

*: interface is up

IHQ: pkts in input hold queue IQD: pkts dropped from input queue

OHQ: pkts in output hold queue OQD: pkts dropped from output queue

RXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)

TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)

TRTL: throttle count

Interface IHQ IQD OHQ OQD RXBS RXPS TXBS TXPS TRTL

-------------------------------------------------------------------------

* Tunnel25 0 0 0 0 0 0 0 0 0

Tunnel50 0 0 0 0 0 0 0 0 0

GigabitEthernet1/1 0 0 0 0 0 0 0 0 0

GigabitEthernet1/2 0 0 0 0 0 0 0 0 0

GigabitEthernet1/3 0 0 0 0 0 0 0 0 0

GigabitEthernet1/4 0 0 0 0 0 0 0 0 0

GigabitEthernet1/5 0 0 0 0 0 0 0 0 0

GigabitEthernet1/6 0 0 0 0 0 0 0 0 0

GigabitEthernet1/7 0 0 0 0 0 0 0 0 0

GigabitEthernet1/8 0 0 0 0 0 0 0 0 0

GigabitEthernet1/9 0 0 0 0 0 0 0 0 0

GigabitEthernet1/10 0 0 0 0 0 0 0 0 0

GigabitEthernet1/11 0 0 0 0 0 0 0 0 0

Kevin Melton Fri, 09/26/2008 - 06:19

Prkrishn

Unfortunantly it was not "sho int summ" either. To try to be more descriptive, I can tell you that it was very similar in nature to "sho ip int brief", but it also had the ports descriptions on it. That being said, it was not "sho int des", as it had one more column of data within it.

Thanks

Kevin

Actions

This Discussion