Simple Outbound Call

Unanswered Question
Oct 8th, 2008

Hi,

We are evaluating CCM 6.0.1. We want to test an outbound call. Here's the setup. We have a 2651XM router with VWIC-1MFT-E1 configured as ISDN-PRI for voice. This gateway is already registered to the CCM. The ISDN-PRI is connected to Avaya PBX and they said they are ready to accept calls from us going to outside lines.

Now, what are the steps I needed to do in the Cisco Call Manager Console? I really don't know what to do. Thanks.

Regards,

John

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 4 (2 ratings)
Loading.
Md. Mijanur Rahman Thu, 10/09/2008 - 00:18

It's simple.

If it's the H.323 Gateway, at CUCM,

1. Go to Route/Hunt>Route Pattern

2. In the 'Route Pattern' match your numbering plan you are dialing (if you are dialing the numbering plan from 123456 to 123789, then put there 123XXX#, or 1!#

3. In the Numbering Plan, select the correct one (hopefully NANP),

4. Select the Gateway you have already added as H.323 gateway.

In the gateway make a pots dial peer:

#conf t

(config)# dial-peer voice 1234 pots

(config)# description **** Outbound ****

(config)# destination-pattern 123...

(config)# no digit-strip

(config)# port

(config)# forward-digits all

Hope this will work if it's the H.323 gateway, is it H.323 or MGCP?

John Patrick Lopez Thu, 10/09/2008 - 02:45

Hi,

Thank you so much for your reply. I am using MGCP I will post my current configuration and please help check if I did something wrong or something not really important.

PHMNLGTW001#sh running-config

Building configuration...

Current configuration : 6466 bytes

!

! Last configuration change at 07:57:03 GMT Thu Oct 9 2008 by john.lopez

! NVRAM config last updated at 16:56:32 GMT Wed Oct 8 2008

!

version 12.4

service timestamps debug datetime msec

service timestamps log datetime msec

service password-encryption

!

hostname PHMNLGTW001

!

boot-start-marker

boot system flash:c2600-a3jk9s-mz.123-11.T10.bin

boot system flash:c2600-js2-mz.123-8.T11.bin

boot system flash:c2600-advipservicesk9-mz.123-22a.bin

boot system flash:c2600-advipservicesk9-mz.124-12.bin

boot-end-marker

!

logging buffered 20000 debugging

!

aaa new-model

!

!

!

aaa session-id common

clock timezone GMT 0

network-clock-participate slot 1

no network-clock-participate wic 0

voice-card 1

!

ip cef

!

!

!

!

no ip domain lookup

ip host CCM-demo 10.199.32.106

!

isdn switch-type primary-net5

isdn logging

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

!

controller E1 1/0

framing NO-CRC4

pri-group timeslots 1-30 service mgcp

!

!

!

!

!

interface FastEthernet0/0

ip address 10.199.1.80 255.255.255.0

duplex auto

speed auto

!

interface FastEthernet0/1

no ip address

shutdown

duplex auto

speed auto

!

interface Serial1/0:15

no ip address

encapsulation hdlc

isdn switch-type primary-net5

isdn incoming-voice voice

isdn bind-l3 ccm-manager

no cdp enable

!

ip route 0.0.0.0 0.0.0.0 10.199.1.1

!

!

ip http server

ip http authentication local

no ip http secure-server

!

!

!

!

control-plane

!

!

!

voice-port 1/0:15

no echo-cancel enable

cptone PH

!

ccm-manager mgcp

ccm-manager music-on-hold

ccm-manager config dialpeer-prefix 200

!

mgcp

mgcp call-agent CCM-demo 2427 service-type mgcp version 0.1

mgcp dtmf-relay voip codec all mode out-of-band

mgcp rtp unreachable timeout 1000 action notify

mgcp modem passthrough voip mode nse

mgcp package-capability rtp-package

no mgcp package-capability res-package

mgcp package-capability sst-package

no mgcp package-capability fxr-package

mgcp package-capability pre-package

no mgcp timer receive-rtcp

mgcp sdp simple

no mgcp explicit hookstate

mgcp rtp payload-type g726r16 static

!

mgcp profile default

!

!

!

!

!

!

line con 0

line aux 0

line vty 0 4

exec-timeout 0 0

logging synchronous

!

ntp clock-period 17208371

ntp server 10.199.32.2

ntp server 10.199.32.3

!

end

PHMNLGTW001#

Marwan ALshawi Thu, 10/09/2008 - 03:27

use the links bellow helpful for u :

How to Configure MGCP with Digital PRI and Cisco CallManager

http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a00801ad22f.shtml

the following one helpful to understand how to make route pattrens

MGCP with Digital CAS and Cisco CallManager Configuration Example

http://www.cisco.com/en/US/tech/tk1077/technologies_configuration_example09186a008022eaa3.shtml

good luck

if helpful Rate

John Patrick Lopez Thu, 10/09/2008 - 06:19

Thank you so much. It helped a lot. We were able to make it work by tweaking Route Pattern. Thanks guys. =)

Actions

This Discussion