10-16-2008 03:56 PM - edited 03-03-2019 11:57 PM
I have a clear P-to-P t3 circuti through AT$T, both routers and their Ser 2/0 are configured exactly the same
Current configuration : 3107 bytes
!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname xxx
!
boot-start-marker
boot system flash:c3845-advipservicesk9-mz.124-16b.bin
boot-end-marker
!
card type t3 2
logging buffered 51200 warnings
enable secret xxx
!
no aaa new-model
ip cef
!
!
ip domain name equitymethods.com
!
voice-card 0
no dspfarm
!
!
!
crypto pki trustpoint TP-self-signed-3555988581
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-3555988581
revocation-check none
rsakeypair TP-self-signed-3555988581
!
crypto pki certificate chain TP-self-signed-3555988581
certificate self-signed 01
xxx !
controller T3 2/0
clock source line
cablelength 70
interface GigabitEthernet0/0
ip address 10.10.30.1 255.255.255.0
duplex auto
speed auto
media-type rj45
!
interface GigabitEthernet0/1
no ip address
shutdown
duplex auto
speed auto
media-type rj45
!
interface Serial2/0
bandwidth 44210
ip address 10.20.50.1 255.255.255.248
dsu bandwidth 44210
!
ip default-gateway 10.20.50.2
ip route 0.0.0.0 0.0.0.0 10.20.50.2
ip route 172.16.200.0 255.255.255.0 10.10.30.2
ip route 172.16.255.0 255.255.255.0 10.10.30.2
!
!
ip http server
no ip http secure-server
control-plane
ORLNDMESA001#sh controller t3
T3 2/0 is down.
Applique type is Subrate T3
Receiver has remote alarm.
MDL transmission is disabled
FEAC code received: No code is being received
Framing is C-BIT Parity, Line Code is B3ZS, Clock Source is Line
Data in current interval (80 seconds elapsed):
0 Line Code Violations, 0 P-bit Coding Violation
0 C-bit Coding Violation, 0 P-bit Err Secs
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs
80 Unavailable Secs, 0 Line Errored Secs
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
Total Data (last 1 15 minute intervals):
0 Line Code Violations, 7 P-bit Coding Violation,
0 C-bit Coding Violation, 0 P-bit Err Secs,
0 P-bit Severely Err Secs, 0 Severely Err Framing Secs,
900 Unavailable Secs, 0 Line Errored Secs,
0 C-bit Errored Secs, 0 C-bit Severely Errored Secs
I know the clocksource says "line" but I was grasping I changed it back to internal and both routers (3845's with NM-1T3/E3 Modules) are exactl;y the same
On my cards I have an "AL" light amber and my "FERF/RAI" light is amber
If I disconnect the cable and place a connector in and loop back the cable at one end my alarm lights go off at the distant end
10-16-2008 05:17 PM
Nevermind, I found the problem
10-17-2008 01:44 PM
Just curious, what was the problem?
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: