11-03-2008 01:38 AM - edited 03-06-2019 02:16 AM
i have 3750 Switch connected by layer to another of same model but eigrp doesnot advertise some static routes although it does it for other neighbours
11-03-2008 01:45 AM
Can you paste the routing config ?
11-03-2008 01:53 AM
As requested by Satish, please post
1) Configuration details
2) routing tables
3) An explanation of which statics work and which don't.
Are you redistributing statics into EIGRP ?
Jon
11-03-2008 03:21 AM
i have EDS Switch which have static route 192.72.24.0 which is not advertised to Access Switch thats why i have to write a Static route, i dont know why only this route is not shown in Access Switch my routing table but have others.although i have it in my EDS Routing Table
attached is the configuration of both the 3750 Switches.
11-03-2008 03:26 AM
Could you clarify. Are any of the static routes on EDS switch showing up in access switch routing table ?
You are not redistributing static routes into EIGRP on EDS switch so it wouldn't get to the access switch.
Apologies if i have misunderstood what you are asking.
Jon
11-03-2008 03:30 AM
yes if you see the routing table of access Switch you can find routes to 172.16.0.0 and other static routes in EDS switch
like
ip route 10.0.0.0 255.240.0.0 10.4.0.13
ip route 10.16.0.0 255.240.0.0 10.4.0.13
ip route 131.2.60.0 255.255.255.0 10.4.0.13
ip route 151.1.2.0 255.255.255.0 10.4.0.13
ip route 151.2.0.0 255.255.0.0 10.4.0.13
ip route 172.16.0.0 255.254.0.0 10.4.0.13
ip route 172.18.0.0 255.254.0.0 10.4.0.13
ip route 192.168.0.0 255.255.255.0 10.4.0.13
except 192.72.24.0
11-03-2008 03:34 AM
Post the output of "show ip route" from both devices please.
11-03-2008 03:26 AM
The reason why the static routes are not being advertised into EIGRP - is because you have not configured EIGRP to advertise static routes.
HTH>
11-03-2008 04:40 AM
Thanks i must redistribute STATIC
11-11-2008 05:38 AM
Hi Guys,
How can you configure EIGRP to advertise static route? Thanks in advance.
Cheers!
Gagamboy15
11-11-2008 05:42 AM
Under your EIGRP configuration
router eigrp 1
redsitribute static
Note that you can use a route-map with the redistribuet static if you only want to advertise some of your statics.
Jon
11-11-2008 04:27 PM
Hi Jon,
Thanks for the reply. Can you please give me a link on where I can study it more deeply? I am not sure If programming statement can also be applied to Network configs like for example:
If this packet came from this destination
then perform this operation.
:-)
Thanks.
Cheers!
Gagamboy
11-11-2008 09:01 PM
Hi Gagamboy,
These docs might be helpful:
Route-Maps for IP Routing Protocol Redistribution Configuration
http://www.cisco.com/en/US/partner/tech/tk365/technologies_tech_note09186a008047915d.shtml
EIGRP Support for Route Map Filtering
http://www.cisco.com/en/US/docs/ios/12_3t/12_3t8/feature/guide/gteigrpr.html
HTH,
~Vaibhav
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: