11-05-2008 06:40 AM - edited 03-04-2019 12:12 AM
I am trying to figure out if I can can channelize 1 DS3 port of a PA-2T3 and have the other port non-channelized, which is interfaces 6/0 and 6/1 (S6/0 is the one I wanted to channelize)
GOMPLS(config)#controller T3 ?
<5-5> Controller slot number
I have another DS3 card and it is the only controller that I have an option for. Any help would be much appreciated!
GOMPLS# sho ver
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-IK9S-M), Version 12.2(15)T17, RELEASE SOFTWARE (fc
1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2005 by cisco Systems, Inc.
Compiled Sat 13-Aug-05 08:20 by kehsiao
Image text-base: 0x60008954, data-base: 0x61DF4000
ROM: System Bootstrap, Version 12.0(19990210:195103) [12.0XE 105], DEVELOPMENT S
OFTWARE
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(5)T1, RELEASE SOFTWARE (fc1
)
GOMPLS uptime is 17 weeks, 6 days, 18 hours, 11 minutes
System returned to ROM by power-on
System restarted at 16:15:17 DST Wed Jul 2 2008
Running default software
cisco 7206VXR (NPE300) processor (revision B) with 229376K/65536K bytes of memor
y.
Processor board ID 16063557
R7000 CPU at 262Mhz, Implementation 39, Rev 1.0, 256KB L2, 2048KB L3 Cache
6 slot VXR midplane, Version 2.0
Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
Primary Rate ISDN software, Version 1.1.
1 FastEthernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
1 Channelized T3 port(s)
125K bytes of non-volatile configuration memory.
46976K bytes of ATA PCMCIA card at slot 0 (Sector size 512 bytes).
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2102
GOMPLS#sho run
interface Serial6/0
no ip address
no ip route-cache
no ip mroute-cache
shutdown
dsu bandwidth 44210
framing c-bit
cablelength 10
serial restart_delay 0
!
interface Serial6/1
ip address 172.x.x.x 255.255.255.252
ip nat inside
ip route-cache flow
no ip route-cache cef
no ip mroute-cache
dsu bandwidth 12288
framing c-bit
cablelength 10
serial restart_delay 0
GOMPLS#sho diag
Slot 5:
CT3 single wide Port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time 17w6d ago
EEPROM contents at hardware discovery:
Hardware revision 1.0 Board revision A0
Serial number 21192556 Part number 73-3037-01
FRU Part Number: PA-MC-T3= (SW)
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 A0 01 00 01 43 5F 6C 49 0B DD 01 00 00 00 00
0x30: 50 00 00 00 00 07 06 00 FF FF FF FF FF FF FF FF
Slot 6:
T3 PA Port adapter, 2 ports
Port adapter is analyzed
Port adapter insertion time 17w6d ago
EEPROM contents at hardware discovery:
Hardware revision 1.0 Board revision A0
Serial number 10738546 Part number 73-2323-02
FRU Part Number: PA-2T3=
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 53 01 00 00 A3 DB 72 49 09 13 02 00 00 00 00
0x30: 50 00 00 00 98 11 06 00 FF FF FF FF FF FF FF FF
Solved! Go to Solution.
11-05-2008 09:14 AM
Mark,
Unlike the PA-MC-T3, the PA-2T3 doesn't support Channelized T3.
Regards
11-05-2008 09:14 AM
Mark,
Unlike the PA-MC-T3, the PA-2T3 doesn't support Channelized T3.
Regards
11-05-2008 09:58 AM
Thanks hritter!
That's what I thought but could not find anything definitive on Cisco's website.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: