cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
2477
Views
6
Helpful
17
Replies

MPLS TE tunnel not coming up - RSVP issue?

dodgerfan78
Level 1
Level 1

Hello,

I have two routers R2 and R5 back to back and I am trying to create an MPLS TE tunnel between them. R2 already has one tunnel up and running to another router R1.

I think my issue is that no RSVP traffic is being sent by R2 or R5. Here is my interface config on R5 and some show commands:

R5#show run int s2/0

Building configuration...

Current configuration : 143 bytes

!

interface Serial2/0

ip address 192.168.25.5 255.255.255.0

mpls traffic-eng tunnels

fair-queue 64 256 32

ip rsvp bandwidth 1000 1000

end

R5#show ip int brief s2/0

Interface IP-Address OK? Method Status Protocol

Serial2/0 192.168.25.5 YES NVRAM up up

R5#show ip rsvp counters in s2/0

Serial2/0 Recv Xmit Recv Xmit

Path 0 0 Resv 0 0

PathError 0 0 ResvError 0 0

PathTear 0 0 ResvTear 0 0

ResvConfirm 0 0 ResvTearConfirm 0 0

UnknownMsg 0 0 Errors 0 0

R5#

I have mpls traffic-eng tunnels on all routers and interfaces. Here here is my tunnel config on R5 towards R2:

R5#show run int tun 2

Building configuration...

Current configuration : 174 bytes

!

interface Tunnel2

ip unnumbered Loopback0

tag-switching ip

tunnel destination 10.0.0.2

tunnel mode mpls traffic-eng

tunnel mpls traffic-eng path-option 1 dynamic

end

I also am learning all addresses via OSPF so R5 does have a route (and can ping) 10.0.0.2 (R2's loopback)

Any ideas where this is failing? Why isn't RSVP sending packets?

Thanks,

1 Accepted Solution

Accepted Solutions

Bryan,

Please enable "ip cef" on R5 and everything should start working.

Regards

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

View solution in original post

17 Replies 17

Giuseppe Larosa
Hall of Fame
Hall of Fame

Hello Bryan,

interface Tunnel2

ip unnumbered Loopback0

>>tag-switching ip

this doesn't look like correct you need to put mpls traffic-engineering commands

look at this example

http://www.cisco.com/en/US/tech/tk436/tk428/technologies_configuration_example09186a0080093fcb.shtml#configs

you need

tunnel mode mpls traffic-eng

try to remove

tag-switching ip

and each router has to declare its loopback as its mpls traffic-eng router-id inside the OSPF process

Hope to help

Giuseppe

Thank you Guiseppe. I have removed that command and I already do have the tunnel mode set to traffic-eng as you can see in my previous post. Also, in my ospf config I have:

mpls traffic-eng router-id Loopback0

mpls traffic-eng area 0

Thanks for your reply...I am totally stimped on this.

Harold Ritter
Cisco Employee
Cisco Employee

Can you post the output of "show mpls traff tunn tunn2".

Regards

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

Sure.

R5#show mpls traffic-eng tunnels tunnel 2

Name: R5_t2 (Tunnel2) Destination: 10.0.0.2

Status:

Admin: up Oper: down Path: not valid Signalling: Down

path option 1, type dynamic

Config Parameters:

Bandwidth: 0 kbps (Global) Priority: 7 7 Affinity: 0x0/0xFFFF

Metric Type: TE (default)

AutoRoute: disabled LockDown: disabled Loadshare: 0 bw-based

auto-bw: disabled(0/200) 0 Bandwidth Requested: 0

Shortest Unconstrained Path Info:

Path Weight: UNKNOWN

Explicit Route: UNKNOWN

History:

Tunnel:

Time since created: 1 minutes, 41 seconds

Path Option 1:

Last Error: PCALC:: No path to destination, 10.0.0.2

R5#

But R5 does have a path to 10.0.0.2:

R5#ping 10.0.0.2

Type escape sequence to abort.

Sending 5, 100-byte ICMP Echos to 10.0.0.2, timeout is 2 seconds:

!!!!!

Success rate is 100 percent (5/5), round-trip min/avg/max = 32/33/36 ms

R5#

In fact, R5 even has the opaque-lsa for 10.0.0.2:

R5#show ip ospf database opaque-area adv-router 10.0.0.2

OSPF Router with ID (10.0.0.5) (Process ID 1)

Type-10 Opaque Link Area Link States (Area 0)

LS age: 184

Options: (No TOS-capability, DC)

LS Type: Opaque Area Link

Link State ID: 1.0.0.0

Opaque Type: 1

Opaque ID: 0

Advertising Router: 10.0.0.2

LS Seq Number: 80000001

Checksum: 0x46F1

Length: 132

Fragment number : 0

MPLS TE router ID : 10.0.0.2

Link connected to Point-to-Point network

Link ID : 10.0.0.1

Interface Address : 192.168.12.2

Neighbor Address : 192.168.12.1

Admin Metric : 64

Maximum bandwidth : 193000

Maximum reservable bandwidth : 187500

Number of Priority : 8

Priority 0 : 187500 Priority 1 : 187500

Priority 2 : 187500 Priority 3 : 187500

Priority 4 : 187500 Priority 5 : 187500

Priority 6 : 187500 Priority 7 : 187500

Affinity Bit : 0x0

Number of Links : 1

LS age: 182

Options: (No TOS-capability, DC)

LS Type: Opaque Area Link

Link State ID: 1.0.0.1

Opaque Type: 1

Opaque ID: 1

Advertising Router: 10.0.0.2

LS Seq Number: 80000001

Checksum: 0xFEB

Length: 124

Fragment number : 1

Link connected to Point-to-Point network

Link ID : 10.0.0.5

Interface Address : 192.168.25.2

Neighbor Address : 192.168.25.5

Admin Metric : 5

Maximum bandwidth : 2500000

Maximum reservable bandwidth : 125000

Number of Priority : 8

Priority 0 : 125000 Priority 1 : 125000

Priority 2 : 125000 Priority 3 : 125000

Priority 4 : 125000 Priority 5 : 125000

Priority 6 : 125000 Priority 7 : 125000

Affinity Bit : 0x0

Number of Links : 1

R5#

192.168.12.x is the net between R1 and R2 (there is a tunnel there and it is up/up.

192.168.25.x is between R2 and R5.

thanks,

Can you post the config for R2 and R5.

Regards

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

Here you go. I have made some changes since then but nothing major. Just adding interfaces under the OSPF MPLS traffic-eng to see if that will work. Also, there is a couple tunnels you see that I have not started to work on yet. Tunnel 5 on R2 points to R5. Tunnel 2 on R5 points to R2.

=====================================

R2:

R2# show run

Building configuration...

Current configuration : 1965 bytes

!

version 12.2

service timestamps debug datetime msec

service timestamps log datetime msec

no service password-encryption

!

hostname R2

!

logging buffered 16384 debugging

!

!

!

ip subnet-zero

ip cef

!

!

no ip domain-lookup

!

mpls label protocol ldp

mpls traffic-eng tunnels

tag-switching tdp router-id Loopback0

!

!

!

!

!

!

!

!

!

!

interface Loopback0

ip address 10.0.0.2 255.255.255.255

!

interface Tunnel1

ip unnumbered Loopback0

tunnel destination 10.0.0.1

tunnel mode mpls traffic-eng

tunnel mpls traffic-eng path-option 1 dynamic

!

interface Tunnel3

ip unnumbered Loopback0

tag-switching ip

tunnel destination 10.0.0.3

tunnel mode mpls traffic-eng

tunnel mpls traffic-eng path-option 1 dynamic

!

interface Tunnel5

ip unnumbered Loopback0

tunnel destination 10.0.0.5

tunnel mode mpls traffic-eng

tunnel mpls traffic-eng path-option 1 dynamic

!

interface FastEthernet1/0

ip address 205.127.233.242 255.255.254.0

speed 100

full-duplex

!

interface Serial2/0

ip address 192.168.12.2 255.255.255.0

mpls traffic-eng tunnels

fair-queue 64 256 37

ip rsvp bandwidth 1500 1500

!

interface Serial2/1

bandwidth 20000

ip address 192.168.25.2 255.255.255.0

mpls traffic-eng tunnels

fair-queue 64 256 37

ip rsvp bandwidth 1000 1000

!

interface Serial2/2

no ip address

shutdown

!

interface Serial2/3

no ip address

shutdown

!

router ospf 1

router-id 10.0.0.2

log-adjacency-changes

network 10.0.0.2 0.0.0.0 area 0

network 192.168.12.0 0.0.0.255 area 0

network 192.168.23.0 0.0.0.255 area 0

network 192.168.25.0 0.0.0.255 area 0

mpls traffic-eng router-id Loopback0

mpls traffic-eng area 0

mpls traffic-eng interface Serial2/0 area 0

mpls traffic-eng interface Serial2/1 area 0

mpls traffic-eng interface Loopback0 area 0

!

ip classless

ip http server

ip pim bidir-enable

!

!

!

call rsvp-sync

!

!

mgcp profile default

!

dial-peer cor custom

!

!

!

!

line con 0

exec-timeout 0 0

logging synchronous

line aux 0

line vty 0 4

login

!

!

end

R2#

====================================

R5:

R5#show run

Building configuration...

Current configuration : 1492 bytes

!

version 12.2

service timestamps debug uptime

service timestamps log uptime

no service password-encryption

!

hostname R5

!

logging buffered 16384 debugging

!

!

!

ip subnet-zero

!

!

no ip domain-lookup

!

mpls label protocol ldp

mpls traffic-eng tunnels

tag-switching tdp router-id Loopback0

!

!

!

!

!

!

!

!

!

!

interface Loopback0

ip address 10.0.0.5 255.255.255.255

!

interface Tunnel2

ip unnumbered Loopback0

tunnel destination 10.0.0.2

tunnel mode mpls traffic-eng

tunnel mpls traffic-eng path-option 1 dynamic

!

interface Serial2/0

ip address 192.168.25.5 255.255.255.0

mpls traffic-eng tunnels

fair-queue 64 256 32

ip rsvp bandwidth 1000 1000

!

interface Serial2/1

ip address 192.168.45.5 255.255.255.0

shutdown

mpls traffic-eng tunnels

fair-queue 64 256 37

ip rsvp bandwidth 1000 1000

!

interface Serial2/2

no ip address

shutdown

fair-queue 64 256 37

ip rsvp bandwidth 10000 10000

!

interface Serial2/3

no ip address

shutdown

!

router ospf 1

router-id 10.0.0.5

log-adjacency-changes

network 10.0.0.5 0.0.0.0 area 0

network 192.168.25.0 0.0.0.255 area 0

network 192.168.45.0 0.0.0.255 area 0

mpls traffic-eng router-id Loopback0

mpls traffic-eng area 0

mpls traffic-eng interface Serial2/0 area 0

mpls traffic-eng interface Loopback0 area 0

!

ip classless

ip http server

ip pim bidir-enable

!

!

!

call rsvp-sync

!

!

mgcp profile default

!

dial-peer cor custom

!

!

!

!

!

!

end

R5#

======================================

thanks

Bryan,

Please enable "ip cef" on R5 and everything should start working.

Regards

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

OH MAN,

Thank you Harold!!!!

hello my freind i dont know that much about TE but in ur tunnel interface commands u have nt put auto route announce command---> tunnel mpls traffic-eng autoroute announce

interface Tunnel1

ip unnumbered Loopback1

tunnel destination 192.168.1.3

tunnel mode mpls traffic-eng

tunnel mpls traffic-eng autoroute announce (this above command is very important)

tunnel mpls traffic-eng priority 1 1

tunnel mpls traffic-eng bandwidth 300

tunnel mpls traffic-eng path-option 10 dynamic

!

cus ur data cant route if it doesnt know the route. might be it can problem--

static

policy base

auto route

Tarj,

Autoroute announce is not the only way to push traffic through the tunnel. You can also use a static route pointing with the tunnel as the next hop interface or use PBR to set the tunnel as the next hop interface.

Regards

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

yea m8 ur right i know that but if u look in that guy router's sh run configuration he has not mention any autoroute or static route or even PBR in his configuration. in 12 nov post b dodger sh run.

(Here you go. I have made some changes since 12 nov)check that one post above there is full router SH Run n u cant find autoroute or static route command in tunnels. so i thought might be thats problem

Regards

Tarj,

This thread has been solved on Nov 12th. "ip cef" was missing from the config.

Regards

Harold Ritter
Sr Technical Leader
CCIE 4168 (R&S, SP)
harold@cisco.com
México móvil: +52 1 55 8312 4915
Cisco México
Paseo de la Reforma 222
Piso 19
Cuauhtémoc, Juárez
Ciudad de México, 06600
México

thanks m8 i have one problem now m tryin to use mpls auto bandwidth adjustment command but problem is when i put two commands togather one disappear from list

1. tunnel mpls traffic-eng auto-bw frequency 600

2. tunnel mpls traffic-eng auto-bw max-bw 60 min-bw 30

why according to cisco lab i can put two commands togather if i remove one then other one comes up. but problem is i want to decrease the time of readjust ment by default it is 24 hour 86400 sec. i put 300 sec n set bandwidth min max they both r oppsite. m using 3660 router on dayangen.

configuration

----------------------------

interface Tunnel1

ip unnumbered Loopback9

tunnel destination 192.168.1.5

tunnel mode mpls traffic-eng

tunnel mpls traffic-eng autoroute announce

tunnel mpls traffic-eng priority 1 1

tunnel mpls traffic-eng bandwidth 50

tunnel mpls traffic-eng path-option 10 dynamic

tunnel mpls traffic-eng auto-bw max-bw 60 min-bw 30

no routing dynamic

end

plz reply soon

i put both commands it appear togather in configuration sh run. but when frequency time 300 finish then bandwidth become 0 cus m using danagen so there is no traffic load. but it should stay to min bandwidth.

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: