2821 Voice Gateway

Answered Question

I need to add more DSP resources to my voicegateway. I currently have 1 PVDMII 32 with 2 16 channel dsp ( I am guessing on the motherboard). My question is can I just order another PVDMII 32 and add this to my mother board? Or do I need some type of NM to do this?


dfwdls-2821-01#sh voice dsp group all

DSP groups on slot 0:

dsp 1:

State: UP, firmware: 8.4.1

Max signal/voice channel: 16/16

Max credits: 240

Group: FLEX_GROUP_VOICE, complexity: FLEX

Shared credits: 240, reserved credits: 0

Signaling channels allocated: 7

Voice channels allocated: 0

Credits used: 0


dsp 2:

State: UP, firmware: 8.4.1

Max signal/voice channel: 16/16

Max credits: 240

Group: FLEX_GROUP_VOICE, complexity: FLEX

Shared credits: 240, reserved credits: 0

Signaling channels allocated: 16

Voice channels allocated: 0

Credits used: 0



DSP groups on slot 1:

This command is not applicable to slot 1


dfwdls-2821-01#sh voice dsp group all

DSP groups on slot 0:

dsp 1:

State: UP, firmware: 8.4.1

Max signal/voice channel: 16/16

Max credits: 240

Group: FLEX_GROUP_VOICE, complexity: FLEX

Shared credits: 240, reserved credits: 0

Signaling channels allocated: 7

Voice channels allocated: 0

Credits used: 0


dsp 2:

State: UP, firmware: 8.4.1

Max signal/voice channel: 16/16

Max credits: 240

Group: FLEX_GROUP_VOICE, complexity: FLEX

Shared credits: 240, reserved credits: 0

Signaling channels allocated: 16

Voice channels allocated: 0

Credits used: 0



DSP groups on slot 1:

This command is not applicable to slot 1


DSP groups on slot 2:

This command is not applicable to slot 2


0 DSP resource allocation failure

dfwdls-2821-01#sh inventory

NAME: "2821 chassis", DESCR: "2821 chassis"

PID: CISCO2821 , VID: V04, SN:


NAME: "One port T1 voice interface daughtercard on Slot 0 SubSlot 0", DESCR: "On

e port T1 voice interface daughtercard"

PID: VWIC-1MFT-T1= , VID: 1.0, SN:


NAME: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1 on Slot 0 SubSlot

2", DESCR: "VWIC2-1MFT-T1/E1 - 1-Port RJ-48 Multiflex Trunk - T1/E1"

PID: VWIC2-1MFT-T1/E1 , VID: V01 , SN:


NAME: "PVDMII DSP SIMM with Two DSPs on Slot 0 SubSlot 4", DESCR: "PVDMII DSP SI

MM with Two DSPs"

PID: PVDM2-32 , VID: NA , SN:


Correct Answer by allan.thomas about 8 years 7 months ago

The ISR 2821 has three onboard PVDM slots, therefore it is possible to add a 2nd or 3rd PVDM2-32 if required.


Your 'show inv' only indicates the single PVDM, therefore you should be able to add two additional PVDMs


Hope this helps.

Allan.


Pls rate helpful posts.


  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
Correct Answer
allan.thomas Wed, 11/12/2008 - 15:33
User Badges:
  • Blue, 1500 points or more

The ISR 2821 has three onboard PVDM slots, therefore it is possible to add a 2nd or 3rd PVDM2-32 if required.


Your 'show inv' only indicates the single PVDM, therefore you should be able to add two additional PVDMs


Hope this helps.

Allan.


Pls rate helpful posts.


Actions

This Discussion