Load balance using vlans on Catalyst & hp procurve final

Unanswered Question
Nov 18th, 2008
User Badges:

Just for closing this conversation.

Hello you all.


Well this is the MSTP configuration I think could work. The network schema is in the attachment.


& one more question witch software to use for simulating a catalyst 6500 or another MSTP capable switch?


Thanks


Now the config(according to my schema):


DS1 (catalyst 6500)


interface Fasethernet 7/2

switchport mode trunk

switchport encapsulation dot1Q

switch trunk allowed vlan 1,2,3

switchport nonegociate


interface Fasethernet 7/3

switchport mode trunk

switchport encapsulation dot1Q

switch trunk allowed vlan 2,4,5

switchport nonegociate


interface Fasethernet 7/4

switchport mode trunk

switchport encapsulation dot1Q

switch trunk allowed vlan 4,5,6

switchport nonegociate


spanning-tree mode mst

spanning-tree extend system-id

.

spanning-tree mst configuration

name procurve-cisco

revision 1

instance 1 vlan 1, 3, 5

instance 2 vlan 2, 4, 6

spanning-tree mst 0-1 priority 0

spanning-tree mst 2 priority 4096


DS2(catalyst 6500)


interface Fasethernet 7/2

switchport mode trunk

switchport encapsulation dot1Q

switch trunk allowed vlan 1,2,3

switchport nonegociate


interface Fasethernet 7/3

switchport mode trunk

switchport encapsulation dot1Q

switch trunk allowed vlan 2,4,5

switchport nonegociate


interface Fasethernet 7/4

switchport mode trunk

switchport encapsulation dot1Q

switch trunk allowed vlan 4,5,6

switchport nonegociate


spanning-tree mode mst

spanning-tree extend system-id

.

spanning-tree mst configuration

name procurve-cisco

revision 1

instance 1 vlan 1, 3, 5

instance 2 vlan 3, 4, 6

spanning-tree mst 0-1 priority 4096

spanning-tree mst 2 priority 0




AS1(hp procurve 2600)

vlan 1,2,3,4,5,6

vlan 1 tagged 25, 26

vlan 1 untagged 1-4

vlan 2 tagged 25, 26

vlan 2 untagged 5-6

vlan 3 tagged 25, 26

vlan 3 untagged 7-12

spanning-tree

spanning-tree protocol-version MSTP

spanning-tree config-name "procurve-cisco"

spanning-tree config-revision 1

spanning-tree instance 1 vlan 1 2 3

spanning-tree instance 2 vlan 2 4 6

spanning-tree 1-24 edge-port


AS2(hp procurve 2626)

vlan 1,2,3,4,5,6

vlan 2 tagged 25, 26

vlan 2 untagged 1-4

vlan 4 tagged 25, 26

vlan 4 untagged 5-6

vlan 5 tagged 25, 26

vlan 5 untagged 7-12

spanning-tree

spanning-tree protocol-version MSTP

spanning-tree config-name "procurve-cisco"

spanning-tree config-revision 1

spanning-tree instance 1 vlan 1 2 3

spanning-tree instance 2 vlan 2 4 6

spanning-tree 1-24 edge-port


AS3(hp procurve 2626)

vlan 1,2,3,4,5,6

vlan 4 tagged 25, 26

vlan 4 untagged 1-4

vlan 5 tagged 25, 26

vlan 5 untagged 5-6

vlan 6 tagged 25, 26

vlan 6 untagged 7-12

spanning-tree

spanning-tree protocol-version MSTP

spanning-tree config-name "procurve-cisco"

spanning-tree config-revision 1

spanning-tree instance 1 vlan 1 2 3

spanning-tree instance 2 vlan 2 4 6

spanning-tree 1-24 edge-port


Thanks for any comments.





Attachment: 
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
Giuseppe Larosa Wed, 11/19/2008 - 07:26
User Badges:
  • Super Silver, 17500 points or more
  • Hall of Fame,

    Founding Member

Hello Osvaldo,

the configuration looks like fine.


About MSTP emulation there are packages for instruments like Agilent router tester or IXIA but they work on dedicated hardware.


I don't know if under linux or freebsd you can find something useful.


Hope to help

Giuseppe



languedoc Sun, 11/23/2008 - 12:21
User Badges:

Hi Giuseppe.

I thank you very much.

You are very nice.

Thanks again.

I think I can close this conversation.


Bye

Actions

This Discussion