MPLS TE over Port-channel interfaces

slandreth · ‎11-20-2008

I get the following 'warning' when configuring MPLS TE on a port-channel interface. Any comments on what the limitations to using TE on a port-channel interface are?

7606(config)#interface port-channel99

7606(config-if)#mpls traffic-eng tunnels

%Warning: MPLS TE support is limited for port-channel interfaces.

For additional information, please contact the MPLS TE product manager.

smahbub · ‎11-27-2008

I think that you might be hitting the bug CSCsi55462.Traffic Engineering is not a supported configuration under

port-channel interface. However, limited support for Traffic

Engineering is allowed with the following caveats:

1) Zero bandwidth tunnel

2) No FRR support

minhtu_pro · ‎12-02-2008

Hi,

I configured TE and FRR on Port-Channel also. I saw some TE Tunnels worked with FRR, some didn't. I enclose here for reference.

Router#sho mpls traffic-eng fast-reroute database

Headend frr information:

Protected tunnel In-label Out intf/label FRR intf/label Status

Tunnel1000 Tun hd Po1:implicit-nul Tu1004:implicit- ready

Tunnel1001 Tun hd Po2:implicit-nul Tu1005:implicit- ready

LSP midpoint frr information:

LSP identifier In-label Out intf/label FRR intf/label Status

Router#show mpls traffic-eng tunnels brief

Signalling Summary:

LSP Tunnels Process: running

Passive LSP Listener: running

RSVP Process: running

Forwarding: enabled

Periodic reoptimization: every 10 seconds, next in 8 seconds

Periodic FRR Promotion: every 300 seconds, next in 146 seconds

Periodic auto-bw collection: every 300 seconds, next in 133 seconds

TUNNEL NAME DESTINATION UP IF DOWN IF STATE/PROT

CISCO ISC-P139 172.16.254.253 - Po1 up/up

CISCO ISC-P141 172.16.254.252 - Po2 up/up

CISCO ISC-P145 172.16.254.251 - Po1 up/up

CISCO ISC-P147 172.16.254.250 - Po2 up/up

CISCO ISC-B181 172.16.254.253 - Po2 up/up

CISCO ISC-B182 172.16.254.252 - Po1 up/up

CISCO ISC-P166 172.16.254.254 Po2 - up/up

CISCO ISC-B187 172.16.254.252 Po1 Po2 up/up

CISCO ISC-B188 172.16.254.251 Po2 Po1 up/up

CISCO ISC-P159 172.16.254.254 Po1 - up/up

CISCO ISC-B185 172.16.254.250 Po1 Po2 up/up

CISCO ISC-B186 172.16.254.253 Po2 Po1 up/up

CISCO ISC-P173 172.16.254.254 Po2 - up/up

CISCO ISC-P174 172.16.254.253 Po2 Po1 up/up

CISCO ISC-B189 172.16.254.254 Po1 - up/up

CISCO ISC-B190 172.16.254.250 Po2 Po1 up/up

CISCO ISC-P153 172.16.254.252 Po1 Po2 up/up

CISCO ISC-P155 172.16.254.254 Po1 - up/up

CISCO ISC-B183 172.16.254.251 Po1 Po2 up/up

CISCO ISC-B184 172.16.254.254 Po2 - up/up

Displayed 6 (of 6) heads, 8 (of 8) midpoints, 6 (of 6) tails

Can you explain more detail about the limited support for TE on Port-channel?

Many thanks

minhtu_pro · ‎12-04-2008

Hi all,

I make some configuration mistake. It'w fixed and now all TE tunnel work with FRR.

By the way, can anyone explain more about the limited support for TE on port-channel?

Thanks anyway,

Laurent Aubert · ‎12-04-2008

Hi,

Full supportcomes with 12.2(33)SRC:

http://www.cisco.com/en/US/docs/ios/mpls/configuration/guide/mp_bundle_interface_ps6922_TSD_Products_Configuration_Guide_Chapter.html

Hope this helps

Thanks

Laurent.

j.colmenares · ‎11-07-2014

Hi, we have a similar problem. We aer trying configure MPLS TE under poertchannel interface, and it's not is not recognized. We have two chassis 6509 in VSS.

So, we need help.

Thanks.