Problem in COR while configuring in CCME

Unanswered Question
Nov 26th, 2008
User Badges:

i have configured COR by referrin to a doc but COR is not blocking any patterns as i configured.Here is the configuration..


dial-peer cor custom

name .T

name .0T

name .00T

!

dial-peer cor list localcall

member .T

!

dial-peer cor list nationalcall

member .0T

!

dial-peer cor list internationalcall

member .00T

!

dial-peer cor list users

member .T

!

dial-peer cor list Supervisiors

member .T

member .0T

!

dial-peer cor list managers

member .T

member .0T

member .00T


ephone-dn 1

number 2000

description 2000

corlist incoming managers

!

!

ephone-dn 2

number 2001

description 2001

corlist incoming managers

!

!

ephone-dn 10

number 2010

description 2010

corlist incoming managers

!

!

ephone-dn 11

number 2011

description 2011

corlist incoming Supervisiors

!

!

ephone-dn 12

number 2012

description 2012

corlist incoming Supervisiors

!

!

ephone-dn 13

number 2013

description 2013

corlist incoming users

!

!

ephone-dn 14

number 2014

description 2014

corlist incoming users

!

!

ephone-dn 15

number 2015

description 2015

corlist incoming users

!

!

ephone-dn 16

number 2016

description 2016

corlist incoming users

!

!

ephone-dn 17

number 2017

description 2017

corlist incoming users

!

!

ephone-dn 18

number 2018

description 2018

corlist incoming users

!

!

ephone-dn 19

number 2019

description 2019

corlist incoming users

!

!

ephone-dn 20

number 2020

description 2020

corlist incoming users


Could you pls guide me here out...


thanks in advance

siva

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
allan.thomas Thu, 11/27/2008 - 03:57
User Badges:
  • Blue, 1500 points or more

Hi Sivakumar,


I believe the issue could be one of two problems or possibly both.


Firstly have you applied the outgoing cor list to the outgoing POTS dial-peer?


For example the corlist outgoing cointernationalcall should be applied to your International POTs dial-peer.


Secondly, as you are using variable length digit-strings, I suspect that these are overlaping and International will be using the National POTs dial-peer for the outbound call-leg.


Run a 'debug voice capi inout' when you attempt to make an outbound International call from an IP Phone which does not the permission.


The debug will indicate which outbound dial-peer was used. If this is the case then you will need to revise the destination-patterns to make them more explicit.


For example, is your local digit dialplan a fixed number of digits starting with a certain prefix. Here in the UK they start with 2-9 and can be 6,7 or 8 digits, at least this defines it from National calls which start 0 and internation which start 00.


dial-peer voice 1000 pots

corlist outgoing LocalPT

destination-pattern 9[2-9].......

forward-digits 8


Hope this helps.

Allan.


Pls rate helpful posts.

Adrian Saavedra Thu, 11/27/2008 - 08:44
User Badges:
  • Gold, 750 points or more

Hi friend,


As Allan said, check if your dial-peers are configured with corlist outgoing.

Please note that if there is no corlist outgoing, any ephone-dn could reach them regardless of its corlist incoming configuration.


Regards,


- Adrián.

sivakumar.kvp Tue, 12/09/2008 - 06:50
User Badges:

Hi,


I have configured outgoing corlist under respective dial-peers but it's still not blocking.Could you guide me to move on further...


regards

siva

Adrian Saavedra Tue, 12/09/2008 - 07:04
User Badges:
  • Gold, 750 points or more

Hi,


Could you paste your new config? (i.e. dial-peers, ephone-dns and dial-peer corlists...).


Regards.

allan.thomas Tue, 12/09/2008 - 08:07
User Badges:
  • Blue, 1500 points or more

Hi Sivakumar,


As I have previously mentioned, if you are using variable length digit-strings then it is possible that these are overlaping.


Run a 'debug voice capi inout' when you attempt to make an outbound International call from an IP Phone which does not the appropriate cor list.


The debug will indicate which outbound dial-peer was used. For example if you dial an international number from an IP Phone which is not permitted, the debug will show which dial-peer was used to place the call.


Please capture the appropriate debug as I have mentioned, and post the results.


Thanks

Allan.



Actions

This Discussion