HW conference bridge

Answered Question
Dec 1st, 2008
User Badges:

Hello folks


I'm trying to configure a 2811 to run as a hw conference bridge

I have 2 PRIs up and running on this GW, I have a PVDM2-64,

however when I'm configuring the dspfarm profile when I try to issue the maximum sessions command the only option is 0, could you point me on the right way to solve this issue

thank you

Correct Answer by jbarcena about 8 years 6 months ago

Indeed you need more resources, what is the output of a 'show voice dsp' and also froma 'show dspfarm all'

  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 5 (1 ratings)
Loading.
jbarcena Mon, 12/01/2008 - 14:52
User Badges:
  • Red, 2250 points or more

Take a 'show diag' and upload the result.

cris_jimenez Mon, 12/01/2008 - 14:55
User Badges:

2811-633-data2#sh diag

Slot 0:

C2811 Motherboard with 2FE and integrated VPN Port adapter, 2 ports

Port adapter is analyzed

Port adapter insertion time unknown

EEPROM contents at hardware discovery:

PCB Serial Number : FOC12250Y7B

Hardware Revision : 1.0

Top Assy. Part Number : 800-26920-04

Board Revision : A0

Deviation Number : 0

Fab Version : 04

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 87

Hardware date code : 20080621

Chassis Serial Number : FTX1228A03R

Chassis MAC Address : 0021.d828.e308

MAC Address block size : 24

CLEI Code : COM7R00ARA

Product (FRU) Number : CISCO2811

Part Number : 73-10258-05

Version Identifier : V05

EEPROM format version 4

EEPROM contents (hex):

PVDM Slot 0:

64-channel (G.711) Voice/Fax PVDMII DSP SIMM PVDM daughter card

Hardware Revision : 4.0

Part Number : 73-8541-05

Board Revision : B0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC12255AXK

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Processor type : 00

Product (FRU) Number : PVDM2-64

Version Identifier : V01

EEPROM format version 4

EEPROM contents (hex):

0x00: 04 FF 40 03 EC 41 04 00 82 49 21 5D 05 42 42 30

0x10: 88 00 00 00 00 02 04 C1 8B 46 4F 43 31 32 32 35

0x20: 35 41 58 4B 03 00 81 00 00 00 00 04 00 09 00 CB

0x30: 88 50 56 44 4D 32 2D 36 34 89 56 30 31 20 D9 02

0x40: 40 C1 FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x50: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF

0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF


WIC Slot 0:

VWIC2-2MFT-T1/E1 - 2-Port RJ-48 Multiflex Trunk - T1/E1

Hardware Revision : 0.0

Top Assy. Part Number : 800-22629-05

Board Revision : B0

Deviation Number : 0

Fab Version : 04

PCB Serial Number : FOC12246J8P

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : VWIC2-2MFT-T1/E1

Version Identifier : V01

EEPROM format version 4

WIC Slot 1:

2nd generation - FXO Voice daughter card (4 port)

Hardware Revision : 5.0

Top Assy. Part Number : 800-21589-04

Board Revision : A0

Deviation Number : 0-0

Fab Version : 04

PCB Serial Number : FOC122414GY

RMA Test History : 00

RMA Number : 0-0-0-0

RMA History : 00

Product (FRU) Number : VIC2-4FXO

Version Identifier : V03

CLEI Code : CNUIAXJAAB

EEPROM format version 4

cris_jimenez Mon, 12/01/2008 - 15:23
User Badges:

I haven't tried that yet. but i'm pretty sure that if I remove one i will get 4 dsp channels

Correct Answer
jbarcena Mon, 12/01/2008 - 15:24
User Badges:
  • Red, 2250 points or more

Indeed you need more resources, what is the output of a 'show voice dsp' and also froma 'show dspfarm all'

Jaime Valencia Mon, 12/01/2008 - 15:29
User Badges:
  • Cisco Employee,
  • Hall of Fame,

    2011

actually a DSP means 16 channels, that's why the PVDM2-64 has 4 DSPs. a PVDM2-8 is only half DSP, 8 channels.


you have 2 T1/E1 on that card and a 4FXO card


most probably you're not leaving the whole DSP that is required to configure CFB, meaning 16 channels. a sh voice dsp and a sh run can confirm this.


if you're using both T1s + 4fxo those are 52 channels out of 64, meaning you don't have enough resources. if using both E1s and no FXOs then that leaves even less resources free


HTH


java


if this helps, please rate

Actions

This Discussion