12-03-2008 02:54 PM - edited 03-15-2019 02:54 PM
Hello, I am new to this site but would like to dive right in. I have recently set up a CME 7.0 for use with a 7921 wireless phone. I can get the 7921 to register with the CME butit will not aquire the assigned DN and thus cannot make calls. Thanks for any help!!
12-03-2008 06:28 PM
Hi friend,
Could you paste your config?
Regards,
- Adrián.
12-03-2008 09:34 PM
Hi,
I am having the same issue with CME 7.0 which is used with cisco 7961 & 7941. they are registered with CME but not able to aquire the assigned DN and thus cannot make calls.
Can Any One Help Us in this Regards
Any help would be highly appreciated.
12-03-2008 09:38 PM
12-03-2008 10:31 PM
Hello, I noticed on your config that ephone 1 and ephone 2 do not have button assognments. This would keep the phones from working. They should be assigned dn as below
ephone 1
mac-address 0023.331B.57CF
type 7961
button 1:1
ephone 2
mac-address 001F.CA4C.621F
type 7941
button 1:2
Hope this helps your trouble.
12-03-2008 10:21 PM
12-03-2008 10:24 PM
I have also noticed that when the phone is registered and I issue the show ephone 7921 command that the phone does not show as the correct ephone. Just a little more info. Thanks!!
12-04-2008 01:30 AM
Thanks a ton
now i'm able to dial my peer with extension
12-04-2008 03:35 AM
Hi,
again im in trouble..
now not able to dial out..no dial tone
could you please help
12-04-2008 05:59 AM
Hi friend,
If you want to dial out, so you can make calls to PSTN, you need to configure dial-peers in your router.
Here is a guide to configure:
http://www.cisco.com/en/US/docs/ios/12_3/vvf_c/dial_peer/dpeer_c.html
Regards,
- Adrián.
12-04-2008 11:46 AM
Hello,
I am not sure if your post regarding dial peers is in response to my original post or the replies by "netsoft@netsoft.co.in". The trouble I am having is that when the 7921 registers with CME it does not receive the assigned ephone-dn thus I cannot make any internal or external calls. Thanks again for any help in this matter.
Shawn
12-07-2008 10:20 PM
12-08-2008 07:43 AM
Hi,
You need to add the port command on your POTS dial-peer to route calls properly to the PSTN thru PRI or FXO.
Regards,
- Adrián.
12-08-2008 07:43 AM
Good Morning,
The problem with your Dial-Peers is most likley that there are no voice ports assigned to them. You must assign the voice port that is connected to the PSTN connection you are using. Below is an example. Good luck!
dial-peer voice 3 pots
description *****T1 PRI Pots Local Dial-peer*****
destination-pattern 9.......
port 0/0/0:23
!
dial-peer voice 4 pots
description *****T1 PRI Pots Long Distance Dial-peer*****
destination-pattern 91T
port 0/0/0:23
!
dial-peer voice 5 pots
description *****T1 PRI Pots International Dial-peer*****
destination-pattern 9011T
port 0/0/0:23
12-14-2008 10:17 PM
Actually the International dial-Peer is working fine.
dial-peer voice 96 pots
corlist incoming international-call
corlist outgoing international-call
destination-pattern 0.T
direct-inward-dial
port 0/0/0:0
but the local-call dial peer is not working calls are hitting to it but as I can see in debug its going with my secondary dialtone
example 09811111111
dial-peer voice 95 pots
corlist incoming local-call
corlist outgoing local-call
destination-pattern 09T
direct-inward-dial
port 0/0/0:0
!
dial-peer voice 94 pots
corlist outgoing local-call
destination-pattern 9..
!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide