IOS voice translation-rule/profile issue

Unanswered Question
Dec 8th, 2008

Hello everyone... I'm guessing this will be an easy fix, but I don't work with h.323 gateway config often.

I have the carrier delivering DID 5540-5559 (there are a few more ranges like this, but I am concentrating on this one to keep it simple to start off), which I am trying to map to internal extensions 4400-4419. This is the attempt I am making that isn't working:

...

!

voice translation-rule 1

rule 1 /^554/ /440/

rule 2 /^555/ /441/

rule 3 /^556/ /442/

rule 4 /^5573/ /4437/

rule 5 /^5570/ /4430/

rule 6 /^558/ /444/

rule 7 /^5597/ /4457/

rule 8 /^5601/ /4461/

rule 9 /^5612/ /4472/

!

!

voice translation-profile rochester-inbound

translate called 1

!

...

!

voice-port 1/0:0

!

dial-peer voice 4400 voip

destination-pattern 44..

session target ipv4:xxx.xxx.xxx.xxx

dtmf-relay h245-alphanumeric

codec g711ulaw

no vad

!

dial-peer voice 5500 pots

description Inbound calls from PSTN

translation-profile incoming rochester-inbound

destination-pattern 55..

incoming called-number 55..

port 1/0:0

!

...

The result I get from the 'debug voice translation-rule' when I dial 5540 from the PSTN is:

4d06h: //-1/F7578B518377/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x8349

3D70; count=2

4d06h: //-1/xxxxxxxxxxxx/RXRULE/regxrule_get_profile_from_trunkgroup_internal: V

oice port 0x8370A210 does not belong to any trunk group

4d06h: //-1/FD70F089837A/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x8409

937C; count=1

4d06h: //-1/FD70F089837A/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x840

9937C; count=0

4d06h: //-1/FD70F089837A/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x840

9937C; count=1

4d06h: //-1/FD70F089837A/RXRULE/regxrule_dp_translate: No profile found in peer

5500 for outgoing direction

4d06h: //-1/FD70F089837A/RXRULE/regxrule_dp_translate: calling_number= calling_o

ctet=0x0

called_number=5540 called_octet=0x81

redirect_number= redirect_type=0 redirect_plan=0 redirect_PI=0 re

direct_SI=0

4d06h: //-1/FD70F089837A/RXRULE/regxrule_vp_translate: No profile found in voice

port or trunk group for outgoing direction

4d06h: //-1/FD70F089837A/RXRULE/regxrule_vp_translate: calling_number= calling_o

ctet=0x0

called_number=5540 called_octet=0x81

redirect_number= redirect_type=0 redirect_plan=0

4d06h: //-1/FD70F089837A/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x8409

937C; count=2

Using 12.3(4)T1 on this 2621 with only 1 CAS T1 on 1/0:0.

I have this problem too.
0 votes
  • 1
  • 2
  • 3
  • 4
  • 5
Overall Rating: 0 (0 ratings)
Loading.
gogasca Tue, 12/09/2008 - 00:26

I normally use test voice translation rule to test before.

If it is CAS not sure if rules will apply the same.

Could you please run the following debugs:

debug voice ccapi inou

debug vpm signal

debug voice translation-rule

debug dialpeer

thanks

glenn.white Thu, 01/22/2009 - 16:58

Hi, try applying your inbound translation profile to your voice port.

e.g.

!

voice-port 1/0:0

translation-profile incoming rochester-inbound

!

Your voice translation rules (no.s 1&2 at least) are correct.

If you are still having problems post the same debug back in here and add another one with just the dial-peer debugging on.

Glenn

Actions

This Discussion