cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
708
Views
0
Helpful
1
Replies

voip dialing problem

mathieu.ploton
Level 1
Level 1

Hi,

Here is my configuration :

Cisco 2611XM connected to my PABX through E1/T1 interfaces and two remote agencies with INTIP cards on their PABX.

When i dial from my local PABX to site B, it's working fine. When Site A try to dial Site B, it's not working.

It's weird because in the log, I see the same numbers dialing :

Here it's a call from Site A to Site B, using a tempo :

Dec 13 01:29:27 10.55.1.3 53570: Dec 13 01:28:35.104: %VOIPAAA-5-VOIP_CALL_HISTORY: CallLegType 2, ConnectionId 4942BA09 8E3DD4F4 240080 9F048807, SetupTime 01:28:05.264 PARIS Sat Dec 13 2008, PeerAddress 8996111, PeerSubAddress , DisconnectCause 66 , DisconnectText recovery on timer expiry (102), ConnectTime 01:28:35.104 PARIS Sat

Here, it's a call from site A to site B using a number of digits

Dec 13 2008, DisconnectTime 01:28:35.104 PARIS Sat Dec 13 2008, CallOrigin 2, ChargedUnits 0, InfoType 2, TransmitPackets 0, TransmitBytes 0, ReceivePackets 0, ReceiveBytes 0

Dec 13 01:29:47 10.55.1.3 53571: Dec 13 01:28:55.065: %VOIPAAA-5-VOIP_CALL_HISTORY: CallLegType 2, ConnectionId 4942BA3B ABEBBE08 210080 9F048807, SetupTime 01:28:55.045 PARIS Sat Dec 13 2008, PeerAddress 8996111, PeerSubAddress , DisconnectCause 3 , DisconnectText no route to destination (3), ConnectTime 01:28:55.055 PARIS Sat Dec 13 2008, DisconnectTime 01:28:55.055 PARIS Sat Dec 13 2008, CallOrigin 2, ChargedUnits 0, InfoType 2, TransmitPackets 0, TransmitBytes 0, ReceivePackets 0, ReceiveBytes 0

When i try the same, in my local PABX? i see normal call clearing and the Peer Address in my log is the good one (8996111).

My dialpeer :

dial-peer voice 1 pots

description POTS

destination-pattern 669....

progress_ind setup enable 3

progress_ind alert enable 8

progress_ind progress enable 8

progress_ind connect enable 8

translate-outgoing calling 488

no digit-strip

direct-inward-dial

port 1/0:15

forward-digits 5

!

dial-peer voice 11 voip

description SITE A

preference 1

destination-pattern 888T

progress_ind setup enable 1

translate-outgoing called 888

session target ipv4:10.10.10.5

dtmf-relay h245-alphanumeric

no vad

!

dial-peer voice 13 voip

description SITE B

destination-pattern 899T

progress_ind setup enable 1

translate-outgoing called 899

session target ipv4:10.20.10.5

dtmf-relay h245-alphanumeric

no vad

1 Reply 1

aghaznavi
Level 5
Level 5

%VOIPAAA-5-VOIP_CALL_HISTORY:

This message provides call history detail. Call history detail output is used in simple accounting. The ASCII comma-delimited output can be stored using the syslogd command and passed on to other billing or processing software on a server.

Recommended Action: No action is required.

For further information click this link.

CDR Logging Configuration with Syslog Servers and Cisco IOS Gateways [Gateway Protocols]