cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1447
Views
0
Helpful
14
Replies

Prefix FXO line

p.maillot
Level 1
Level 1

Hello,

I Have a FXO card and I want that the extension 100 can take this line.

How to create a prefix to take this line, for example I want to dial 0 to take this line? And how to program a key on the IP Phone to take this line?

voice-port 0/3/0

connection plar 100

Regards

1 Accepted Solution

Accepted Solutions

ok then forward all the dialed digits.

for example for loca calls you will dial 0 then the 7 digits number as below:

dial-peer voice 10 pots

destination-patter 0[2-9]......

port 0/3/0

forward digits 7

try that

View solution in original post

14 Replies 14

Chris Deren
Hall of Fame
Hall of Fame

You need to create a dial peer in order to control outboud calls, i.e.

dial-peer voice 1 pots

destination-pattern 0

port 0/3/0

forward-digits 1

connection plar controls inboud destination, so if a call arrives on this port from the connected device (PSTN) it will be forwarded to extension 100.

HTH,

Chris

Now when I dial the number 0, the call try to take the port 0/3/3 and after the port 0/3/2 and after again the port 0/3/1 before to arrive at the correct line at 0/3/0.

The call don't take directly the port 0/3/0, why?

Regards

plz post your full configuration, you should have something conflicting the mentioned dial-peer.

thx

See my conf.

Now I have an another problem when I try to take my line on port 0/3/0 I can see an activity on this port (green led) but no tone.

!

voice rtp send-recv

!

voice service voip

allow-connections h323 to h323

allow-connections h323 to sip

allow-connections sip to h323

allow-connections sip to sip

supplementary-service h450.12

h323

sip

registrar server expires max 3600 min 3600

!

!

voice class codec 1

codec preference 1 g711ulaw

!

!

!

!

!

!

!

!

!

!

!

!

voice translation-rule 9

rule 1 /^911$/ /911/

rule 2 /^0\(.*\)/ /\1/

!

controller E1 0/0/0

!

controller E1 0/0/1

!

class-map match-all L3-to-L2_VoIP-Cntrl

match ip dscp af31

class-map match-all L3-to-L2_VoIP-RTP

match ip dscp ef

class-map match-all SIP

match protocol sip

class-map match-all RTP

match protocol rtp

!

!

policy-map EthOut

class RTP

policy-map output-L3-to-L2

class L3-to-L2_VoIP-RTP

set cos 5

class L3-to-L2_VoIP-Cntrl

set cos 3

!

!

!

!

!

interface Loopback0

ip address 10.1.10.2 255.255.255.0

!

interface GigabitEthernet0/0

description $FW_OUTSIDE$

ip address dhcp

ip access-group 101 in

ip nat outside

shutdown

duplex auto

speed auto

media-type rj45

!

interface GigabitEthernet0/1

ip address 10.10.10.1 255.255.255.0

ip access-group 100 in

no ip mroute-cache

duplex auto

speed auto

media-type rj45

h323-gateway voip bind srcaddr 10.10.10.1

!

interface Integrated-Service-Engine3/0

no ip address

no keepalive

!

!

!

ip http server

ip http authentication local

ip http secure-server

ip http path flash

!

access-list 100 remark auto generated by SDM firewall configuration

access-list 100 remark SDM_ACL Category=1

access-list 100 deny ip 10.0.0.0 0.0.0.255 any

access-list 100 deny ip host 255.255.255.255 any

access-list 100 deny ip 127.0.0.0 0.255.255.255 any

access-list 100 permit ip any any

access-list 101 remark auto generated by SDM firewall configuration

access-list 101 remark SDM_ACL Category=1

access-list 101 deny ip 20.0.0.0 0.0.0.255 any

access-list 101 permit udp host 205.152.0.20 any

access-list 101 permit icmp any any echo-reply

access-list 101 permit icmp any any time-exceeded

access-list 101 permit icmp any any unreachable

access-list 101 deny ip 10.0.0.0 0.255.255.255 any

access-list 101 deny ip 172.16.0.0 0.15.255.255 any

access-list 101 deny ip 192.168.0.0 0.0.255.255 any

access-list 101 deny ip 127.0.0.0 0.255.255.255 any

access-list 101 deny ip host 255.255.255.255 any

access-list 101 deny ip host 0.0.0.0 any

access-list 101 deny ip any any log

!

!

tftp-server flash:P00307020200.sbn

tftp-server flash:P00307020200.bin

tftp-server flash:TERM70.7-0-1-0s.LOADS

tftp-server flash:TERM70.DEFAULT.loads

tftp-server flash:TERM71.DEFAULT.loads

tftp-server flash:cnu70.2-7-4-134.sbn

tftp-server flash:Jar70.2-9-0-117.sbn

tftp-server flash:CVM70.2-0-0-112.sbn

!

control-plane

!

!

!

voice-port 0/1/0

!

voice-port 0/1/1

!

voice-port 0/1/2

!

voice-port 0/1/3

!

voice-port 0/2/0

connection plar opx 601

caller-id enable

!

voice-port 0/2/1

connection plar opx 601

caller-id enable

!

voice-port 0/2/2

connection plar opx 601

caller-id enable

!

voice-port 0/2/3

connection plar opx 601

caller-id enable

!

voice-port 0/3/0

connection plar 100

caller-id enable

!

voice-port 0/3/1

connection plar opx 601

caller-id enable

!

voice-port 0/3/2

connection plar opx 601

caller-id enable

!

voice-port 0/3/3

connection plar opx 601

caller-id enable

!

voice-port 4/0/0

!

voice-port 4/0/1

!

voice-port 4/0/2

!

voice-port 4/0/3

!

voice-port 4/0/4

!

voice-port 4/0/5

!

voice-port 4/0/6

!

voice-port 4/0/7

dial-peer cor custom

name internal

name local

name domestic

name international

name 900

name 976

!

!

dial-peer cor list call-internal

member internal

!

dial-peer cor list call-local

member local

!

dial-peer cor list call-domestic

member domestic

!

dial-peer cor list call-international

member international

!

dial-peer cor list call-900

member 900

!

dial-peer cor list call-976

member 976

!

dial-peer cor list user-internal

member internal

!

dial-peer cor list user-local

member internal

member local

!

dial-peer cor list user-domestic

member internal

member local

member domestic

!

dial-peer cor list user-international

member internal

member local

member domestic

member international

!

dial-peer cor list user900-internal

member internal

member 900

member 976

!

dial-peer cor list user900-local

member internal

member local

member 900

member 976

!

dial-peer cor list user900-domestic

member internal

member local

member domestic

member 900

member 976

!

dial-peer cor list user900-international

member internal

member local

member domestic

member international

member 900

member 976

!

!

dial-peer voice 3 pots

corlist outgoing call-local

description ** T1 PRI pots dial-peer **

destination-pattern 9T

!

dial-peer voice 4 pots

corlist outgoing call-domestic

description ** T1 PRI pots dial-peer **

destination-pattern 9T

!

dial-peer voice 5 pots

corlist outgoing call-international

description ** T1 PRI pots dial-peer **

destination-pattern 900T

!

dial-peer voice 6 pots

corlist outgoing call-900

description ** T1 PRI pots dial-peer **

destination-pattern 91900.......

!

dial-peer voice 7 pots

corlist outgoing call-976

description ** T1 PRI pots dial-peer **

destination-pattern 91976.......

!

dial-peer voice 8 pots

description ** T1 PRI pots dial-peer **

incoming called-number .

direct-inward-dial

!

dial-peer voice 9 pots

description ** T1 PRI pots dial-peer **

destination-pattern 911

forward-digits all

!

dial-peer voice 11 pots

corlist outgoing call-local

description ** T1 PRI pots dial-peer **

destination-pattern 9T

!

dial-peer voice 12 pots

corlist outgoing call-domestic

description ** T1 PRI pots dial-peer **

destination-pattern 9T

!

dial-peer voice 13 pots

corlist outgoing call-international

description ** T1 PRI pots dial-peer **

destination-pattern 900T

!

dial-peer voice 14 pots

corlist outgoing call-900

description ** T1 PRI pots dial-peer **

destination-pattern 91900.......

!

dial-peer voice 15 pots

corlist outgoing call-976

description ** T1 PRI pots dial-peer **

destination-pattern 91976.......

!

dial-peer voice 16 pots

description ** T1 PRI pots dial-peer **

incoming called-number .

direct-inward-dial

!

dial-peer voice 74 voip

description ** cue voicemail pilot number **

translation-profile outgoing PSTN_CallForwarding

destination-pattern 600

session protocol sipv2

session target ipv4:10.1.10.1

dtmf-relay sip-notify

codec g711ulaw

no vad

!

dial-peer voice 75 voip

description ** cue auto attendant number **

translation-profile outgoing PSTN_CallForwarding

destination-pattern 601

session protocol sipv2

session target ipv4:10.1.10.1

dtmf-relay sip-notify

codec g711ulaw

no vad

!

dial-peer voice 76 pots

destination-pattern 250

port 0/1/0

!

dial-peer voice 77 pots

destination-pattern 0

port 0/3/0

forward-digits 1

telephony-service

load 7960-7940 P00307020200

load 7970 P00307020200

load 7906 P00307020200

max-ephones 150

max-dn 480

ip source-address 10.10.10.1 port 2000

auto assign 110 to 120

caller-id block code *916

calling-number initiator

service phone videoCapability 1

system message Banque Atlantique

time-zone 5

date-format dd-mm-yy

voicemail 600

max-conferences 8 gain -6

call-forward pattern .T

call-forward system redirecting-expanded

moh music-on-hold.au

web admin system name admin secret 5 $1$kscD$yxr4NQKAcnqvH1nO/QPgT/

dn-webedit

time-webedit

transfer-system full-consult dss

transfer-pattern .T

create cnf-files version-stamp 7960 Dec 20 2008 09:06:21

!

!

ephone-dn 1

number 301

name IP-Paging1

paging ip 239.1.1.1 port 2000

!

!

ephone-dn 2

number 302

name IP-Paging2

paging ip 239.1.1.2 port 2000

!

!

ephone-dn 3

number 303

name IP-Paging3

paging ip 239.1.1.3 port 2000

!

!

ephone-dn 4

number 304

name IP-Paging4

paging ip 239.1.1.4 port 2000

!

!

ephone-dn 5 dual-line

number 100 secondary 4085551000

label 100

description User Name

name CISCO

call-forward busy 600

call-forward noan 600 timeout 15

corlist incoming user900-international

!

!

ephone-dn 6 dual-line

number 101 secondary 4085551001

label 101

description User Name

name User Name

call-forward busy 600

call-forward noan 600 timeout 15

corlist incoming user900-international

!

!

ephone-dn 7 dual-line

number 102 secondary 4085551002

label 102

description User Name

name User Name

call-forward busy 600

call-forward noan 600 timeout 15

corlist incoming user900-international

!

!

ephone-dn 8 dual-line

number 103 secondary 4085551003

label 103

description User Name

name User Name

call-forward busy 600

call-forward noan 600 timeout 15

corlist incoming user900-international

!

!

ephone-dn 9 dual-line

number 104 secondary 4085551004

label 104

description User Name

name User Name

call-forward busy 600

call-forward noan 600 timeout 15

corlist incoming user900-international

!

!

ephone-dn 10 dual-line

number 105

label 105

description User Name

name User Name

call-forward busy 600

call-forward noan 600 timeout 15

corlist incoming user900-international

!

!

ephone-dn 151 dual-line

number 246

label 246

description User Name

name User Name

call-forward busy 600

call-forward noan 600 timeout 15

corlist incoming user900-international

!

!

ephone-dn 152 dual-line

number 247

label 247

description User Name

name User Name

call-forward busy 600

call-forward noan 600 timeout 15

corlist incoming user900-international

!

!

ephone-dn 153 dual-line

number 248

label 248

description User Name

name User Name

call-forward busy 600

call-forward noan 600 timeout 15

corlist incoming user900-international

!

!

ephone-dn 154 dual-line

number 249

label 249

description User Name

name User Name

call-forward busy 600

call-forward noan 600 timeout 15

corlist incoming user900-international

!

!

ephone-dn 155

number 800...

mwi on

!

!

ephone-dn 156

number 801...

mwi off

!

!

ephone-dn 157

number 701

park-slot

!

!

ephone-dn 158

number 702

park-slot

!

!

ephone-dn 159

number 703

park-slot

!

!

ephone-dn 160

number 704

park-slot

!

!

ephone-dn 161

number 705

park-slot

!

!

ephone-dn 162

number 706

park-slot

!

!

ephone-dn 163

number 707

park-slot

!

!

ephone-dn 164

number 708

park-slot

!

ephone 1

video

mac-address 0022.90BC.20A8

username "100" password 0000

type 7960

button 1:5

pin 0000

!

!

!

ephone 2

video

mac-address 001C.58F9.8BE1

after-hour exempt

username "user2" password 101

type 7970

button 1:6

!

!

!

ephone 3

video

mac-address 0000.0000.0003

username "user3" password 102

type 7960

button 1:7

!

!

!

ephone 4

video

mac-address 0000.0000.0004

username "user4" password 103

type 7960

button 1:8

!

!

!

ephone 5

video

mac-address 0000.0000.0005

username "user5" password 104

type 7960

button 1:9

!

!

!

ephone 6

video

mac-address 0000.0000.0006

username "user6" password 105

type 7960

button 1:10

!

!

!

ephone 7

video

mac-address 0000.0000.0007

username "user7" password 106

type 7960

!

!

!

ephone 8

video

mac-address 0000.0000.0008

username "user8" password 107

type 7960

!

!

!

ephone 9

video

mac-address 0000.0000.0009

username "user9" password 108

type 7960

!

!

!

ephone 10

video

mac-address 0000.0000.0010

username "user10" password 109

type 7960

!

!

ephone-hunt 1 sequential

pilot 501

final 600

statistics collect

!

!

ephone-hunt 2 sequential

pilot 502

final 600

statistics collect

!

!

ephone-hunt 3 sequential

pilot 503

final 600

statistics collect

!

!

ephone-hunt 4 sequential

pilot 504

final 600

statistics collect

!

!

alias exec cue service-module service-engine 3/0 session

!

line con 0

line aux 0

line 194

no activation-character

no exec

transport preferred none

transport input all

transport output pad telnet rlogin lapb-ta mop udptn v120 ssh

line vty 0 4

privilege level 15

password cisco

login local

transport input telnet ssh

!

scheduler allocate 20000 1000

ntp master

ntp server 10.10.10.1

!

end

CallManager#

looks like fine from the config point of view except im not getting why there is NO T1/E1 for all your dail-peer !!! local LD and international there are not pointing to anything ??!!

now let me understand you well, if you pick up a phone a call "0" only the 4 FXS ports are ringing ??!!!

if yes try to configure :

ephone-dn x

number 0

call-forward all 100

and make sure you can call 100 directly which is the FXS port !!

hope will help..HTH

Actually my analog phone have the number 250

dial-peer voice 76 pots

destination-pattern 250

port 0/1/0

All all extension can call the analog phone

I have put the number "0" to take the FXO port 0/3/0

dial-peer voice 77 pots

destination-pattern 0

port 0/3/0

forward-digits 1

When I dial the number 0 I see an activity on the FXO card but I have no tone

now port 0/3/0 is FXO not FXS ?

if yes what are you trying to achive from your setup ?

call 0 as access code to get line then call outside ?

Port 0/3/0 = FXO

Port 0/1/0 = FXS

Phone 250 is connected on FXS port 0/1/0 and I want dial 0 to take the line 0/3/0 to send an outgoing call.

ok then forward all the dialed digits.

for example for loca calls you will dial 0 then the 7 digits number as below:

dial-peer voice 10 pots

destination-patter 0[2-9]......

port 0/3/0

forward digits 7

try that

With it's running

dial-peer voice 77 pots

destination-patter 0[2-9]......

port 0/3/0

forward digits 0

your config :

dial-peer voice 77 pots

destination-patter 0[2-9]......

port 0/3/0

forward digits 0 <-- this will not send any digit to FXO, so it wont work.

you need to send the calles number to FXO in order to make your call

regards