12-21-2008 01:09 AM - edited 03-15-2019 03:11 PM
Hello,
I Have a FXO card and I want that the extension 100 can take this line.
How to create a prefix to take this line, for example I want to dial 0 to take this line? And how to program a key on the IP Phone to take this line?
voice-port 0/3/0
connection plar 100
Regards
Solved! Go to Solution.
12-22-2008 08:59 AM
ok then forward all the dialed digits.
for example for loca calls you will dial 0 then the 7 digits number as below:
dial-peer voice 10 pots
destination-patter 0[2-9]......
port 0/3/0
forward digits 7
try that
12-21-2008 08:07 AM
You need to create a dial peer in order to control outboud calls, i.e.
dial-peer voice 1 pots
destination-pattern 0
port 0/3/0
forward-digits 1
connection plar controls inboud destination, so if a call arrives on this port from the connected device (PSTN) it will be forwarded to extension 100.
HTH,
Chris
12-22-2008 12:17 AM
Now when I dial the number 0, the call try to take the port 0/3/3 and after the port 0/3/2 and after again the port 0/3/1 before to arrive at the correct line at 0/3/0.
The call don't take directly the port 0/3/0, why?
Regards
12-22-2008 03:31 AM
plz post your full configuration, you should have something conflicting the mentioned dial-peer.
thx
12-22-2008 05:19 AM
See my conf.
Now I have an another problem when I try to take my line on port 0/3/0 I can see an activity on this port (green led) but no tone.
!
voice rtp send-recv
!
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
supplementary-service h450.12
h323
sip
registrar server expires max 3600 min 3600
!
!
voice class codec 1
codec preference 1 g711ulaw
!
!
!
!
!
!
!
!
!
!
!
!
voice translation-rule 9
rule 1 /^911$/ /911/
rule 2 /^0\(.*\)/ /\1/
!
controller E1 0/0/0
!
controller E1 0/0/1
!
class-map match-all L3-to-L2_VoIP-Cntrl
match ip dscp af31
class-map match-all L3-to-L2_VoIP-RTP
match ip dscp ef
class-map match-all SIP
match protocol sip
class-map match-all RTP
match protocol rtp
!
!
policy-map EthOut
class RTP
policy-map output-L3-to-L2
class L3-to-L2_VoIP-RTP
set cos 5
class L3-to-L2_VoIP-Cntrl
set cos 3
!
!
!
!
!
interface Loopback0
ip address 10.1.10.2 255.255.255.0
!
interface GigabitEthernet0/0
description $FW_OUTSIDE$
ip address dhcp
ip access-group 101 in
ip nat outside
shutdown
duplex auto
speed auto
media-type rj45
!
interface GigabitEthernet0/1
ip address 10.10.10.1 255.255.255.0
ip access-group 100 in
no ip mroute-cache
duplex auto
speed auto
media-type rj45
h323-gateway voip bind srcaddr 10.10.10.1
!
interface Integrated-Service-Engine3/0
no ip address
no keepalive
!
!
!
ip http server
ip http authentication local
ip http secure-server
ip http path flash
!
access-list 100 remark auto generated by SDM firewall configuration
access-list 100 remark SDM_ACL Category=1
access-list 100 deny ip 10.0.0.0 0.0.0.255 any
access-list 100 deny ip host 255.255.255.255 any
access-list 100 deny ip 127.0.0.0 0.255.255.255 any
access-list 100 permit ip any any
access-list 101 remark auto generated by SDM firewall configuration
access-list 101 remark SDM_ACL Category=1
access-list 101 deny ip 20.0.0.0 0.0.0.255 any
access-list 101 permit udp host 205.152.0.20 any
access-list 101 permit icmp any any echo-reply
access-list 101 permit icmp any any time-exceeded
access-list 101 permit icmp any any unreachable
access-list 101 deny ip 10.0.0.0 0.255.255.255 any
access-list 101 deny ip 172.16.0.0 0.15.255.255 any
access-list 101 deny ip 192.168.0.0 0.0.255.255 any
access-list 101 deny ip 127.0.0.0 0.255.255.255 any
access-list 101 deny ip host 255.255.255.255 any
access-list 101 deny ip host 0.0.0.0 any
access-list 101 deny ip any any log
!
!
tftp-server flash:P00307020200.sbn
tftp-server flash:P00307020200.bin
tftp-server flash:TERM70.7-0-1-0s.LOADS
tftp-server flash:TERM70.DEFAULT.loads
tftp-server flash:TERM71.DEFAULT.loads
tftp-server flash:cnu70.2-7-4-134.sbn
tftp-server flash:Jar70.2-9-0-117.sbn
tftp-server flash:CVM70.2-0-0-112.sbn
!
control-plane
!
!
!
voice-port 0/1/0
!
voice-port 0/1/1
!
voice-port 0/1/2
!
voice-port 0/1/3
!
voice-port 0/2/0
connection plar opx 601
caller-id enable
!
voice-port 0/2/1
connection plar opx 601
caller-id enable
!
voice-port 0/2/2
connection plar opx 601
caller-id enable
!
voice-port 0/2/3
connection plar opx 601
caller-id enable
!
voice-port 0/3/0
connection plar 100
caller-id enable
!
voice-port 0/3/1
connection plar opx 601
caller-id enable
!
voice-port 0/3/2
connection plar opx 601
caller-id enable
!
voice-port 0/3/3
connection plar opx 601
caller-id enable
!
voice-port 4/0/0
!
voice-port 4/0/1
!
voice-port 4/0/2
!
voice-port 4/0/3
!
voice-port 4/0/4
!
voice-port 4/0/5
!
voice-port 4/0/6
!
voice-port 4/0/7
12-22-2008 05:22 AM
dial-peer cor custom
name internal
name local
name domestic
name international
name 900
name 976
!
!
dial-peer cor list call-internal
member internal
!
dial-peer cor list call-local
member local
!
dial-peer cor list call-domestic
member domestic
!
dial-peer cor list call-international
member international
!
dial-peer cor list call-900
member 900
!
dial-peer cor list call-976
member 976
!
dial-peer cor list user-internal
member internal
!
dial-peer cor list user-local
member internal
member local
!
dial-peer cor list user-domestic
member internal
member local
member domestic
!
dial-peer cor list user-international
member internal
member local
member domestic
member international
!
dial-peer cor list user900-internal
member internal
member 900
member 976
!
dial-peer cor list user900-local
member internal
member local
member 900
member 976
!
dial-peer cor list user900-domestic
member internal
member local
member domestic
member 900
member 976
!
dial-peer cor list user900-international
member internal
member local
member domestic
member international
member 900
member 976
!
!
dial-peer voice 3 pots
corlist outgoing call-local
description ** T1 PRI pots dial-peer **
destination-pattern 9T
!
dial-peer voice 4 pots
corlist outgoing call-domestic
description ** T1 PRI pots dial-peer **
destination-pattern 9T
!
dial-peer voice 5 pots
corlist outgoing call-international
description ** T1 PRI pots dial-peer **
destination-pattern 900T
!
dial-peer voice 6 pots
corlist outgoing call-900
description ** T1 PRI pots dial-peer **
destination-pattern 91900.......
!
dial-peer voice 7 pots
corlist outgoing call-976
description ** T1 PRI pots dial-peer **
destination-pattern 91976.......
!
dial-peer voice 8 pots
description ** T1 PRI pots dial-peer **
incoming called-number .
direct-inward-dial
!
dial-peer voice 9 pots
description ** T1 PRI pots dial-peer **
destination-pattern 911
forward-digits all
!
dial-peer voice 11 pots
corlist outgoing call-local
description ** T1 PRI pots dial-peer **
destination-pattern 9T
!
dial-peer voice 12 pots
corlist outgoing call-domestic
description ** T1 PRI pots dial-peer **
destination-pattern 9T
!
dial-peer voice 13 pots
corlist outgoing call-international
description ** T1 PRI pots dial-peer **
destination-pattern 900T
!
dial-peer voice 14 pots
corlist outgoing call-900
description ** T1 PRI pots dial-peer **
destination-pattern 91900.......
!
dial-peer voice 15 pots
corlist outgoing call-976
description ** T1 PRI pots dial-peer **
destination-pattern 91976.......
!
dial-peer voice 16 pots
description ** T1 PRI pots dial-peer **
incoming called-number .
direct-inward-dial
!
dial-peer voice 74 voip
description ** cue voicemail pilot number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 600
session protocol sipv2
session target ipv4:10.1.10.1
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 75 voip
description ** cue auto attendant number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 601
session protocol sipv2
session target ipv4:10.1.10.1
dtmf-relay sip-notify
codec g711ulaw
no vad
!
dial-peer voice 76 pots
destination-pattern 250
port 0/1/0
!
dial-peer voice 77 pots
destination-pattern 0
port 0/3/0
forward-digits 1
12-22-2008 05:23 AM
telephony-service
load 7960-7940 P00307020200
load 7970 P00307020200
load 7906 P00307020200
max-ephones 150
max-dn 480
ip source-address 10.10.10.1 port 2000
auto assign 110 to 120
caller-id block code *916
calling-number initiator
service phone videoCapability 1
system message Banque Atlantique
time-zone 5
date-format dd-mm-yy
voicemail 600
max-conferences 8 gain -6
call-forward pattern .T
call-forward system redirecting-expanded
moh music-on-hold.au
web admin system name admin secret 5 $1$kscD$yxr4NQKAcnqvH1nO/QPgT/
dn-webedit
time-webedit
transfer-system full-consult dss
transfer-pattern .T
create cnf-files version-stamp 7960 Dec 20 2008 09:06:21
!
!
ephone-dn 1
number 301
name IP-Paging1
paging ip 239.1.1.1 port 2000
!
!
ephone-dn 2
number 302
name IP-Paging2
paging ip 239.1.1.2 port 2000
!
!
ephone-dn 3
number 303
name IP-Paging3
paging ip 239.1.1.3 port 2000
!
!
ephone-dn 4
number 304
name IP-Paging4
paging ip 239.1.1.4 port 2000
!
!
ephone-dn 5 dual-line
number 100 secondary 4085551000
label 100
description User Name
name CISCO
call-forward busy 600
call-forward noan 600 timeout 15
corlist incoming user900-international
!
!
ephone-dn 6 dual-line
number 101 secondary 4085551001
label 101
description User Name
name User Name
call-forward busy 600
call-forward noan 600 timeout 15
corlist incoming user900-international
!
!
ephone-dn 7 dual-line
number 102 secondary 4085551002
label 102
description User Name
name User Name
call-forward busy 600
call-forward noan 600 timeout 15
corlist incoming user900-international
!
!
ephone-dn 8 dual-line
number 103 secondary 4085551003
label 103
description User Name
name User Name
call-forward busy 600
call-forward noan 600 timeout 15
corlist incoming user900-international
!
!
ephone-dn 9 dual-line
number 104 secondary 4085551004
label 104
description User Name
name User Name
call-forward busy 600
call-forward noan 600 timeout 15
corlist incoming user900-international
!
!
ephone-dn 10 dual-line
number 105
label 105
description User Name
name User Name
call-forward busy 600
call-forward noan 600 timeout 15
corlist incoming user900-international
!
!
ephone-dn 151 dual-line
number 246
label 246
description User Name
name User Name
call-forward busy 600
call-forward noan 600 timeout 15
corlist incoming user900-international
!
!
ephone-dn 152 dual-line
number 247
label 247
description User Name
name User Name
call-forward busy 600
call-forward noan 600 timeout 15
corlist incoming user900-international
!
!
ephone-dn 153 dual-line
number 248
label 248
description User Name
name User Name
call-forward busy 600
call-forward noan 600 timeout 15
corlist incoming user900-international
!
!
ephone-dn 154 dual-line
number 249
label 249
description User Name
name User Name
call-forward busy 600
call-forward noan 600 timeout 15
corlist incoming user900-international
!
!
ephone-dn 155
number 800...
mwi on
!
!
ephone-dn 156
number 801...
mwi off
!
!
ephone-dn 157
number 701
park-slot
!
!
ephone-dn 158
number 702
park-slot
!
!
ephone-dn 159
number 703
park-slot
!
!
ephone-dn 160
number 704
park-slot
!
!
ephone-dn 161
number 705
park-slot
!
!
ephone-dn 162
number 706
park-slot
!
!
ephone-dn 163
number 707
park-slot
!
!
ephone-dn 164
number 708
park-slot
!
12-22-2008 05:24 AM
ephone 1
video
mac-address 0022.90BC.20A8
username "100" password 0000
type 7960
button 1:5
pin 0000
!
!
!
ephone 2
video
mac-address 001C.58F9.8BE1
after-hour exempt
username "user2" password 101
type 7970
button 1:6
!
!
!
ephone 3
video
mac-address 0000.0000.0003
username "user3" password 102
type 7960
button 1:7
!
!
!
ephone 4
video
mac-address 0000.0000.0004
username "user4" password 103
type 7960
button 1:8
!
!
!
ephone 5
video
mac-address 0000.0000.0005
username "user5" password 104
type 7960
button 1:9
!
!
!
ephone 6
video
mac-address 0000.0000.0006
username "user6" password 105
type 7960
button 1:10
!
!
!
ephone 7
video
mac-address 0000.0000.0007
username "user7" password 106
type 7960
!
!
!
ephone 8
video
mac-address 0000.0000.0008
username "user8" password 107
type 7960
!
!
!
ephone 9
video
mac-address 0000.0000.0009
username "user9" password 108
type 7960
!
!
!
ephone 10
video
mac-address 0000.0000.0010
username "user10" password 109
type 7960
!
!
ephone-hunt 1 sequential
pilot 501
final 600
statistics collect
!
!
ephone-hunt 2 sequential
pilot 502
final 600
statistics collect
!
!
ephone-hunt 3 sequential
pilot 503
final 600
statistics collect
!
!
ephone-hunt 4 sequential
pilot 504
final 600
statistics collect
!
!
alias exec cue service-module service-engine 3/0 session
!
line con 0
line aux 0
line 194
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
line vty 0 4
privilege level 15
password cisco
login local
transport input telnet ssh
!
scheduler allocate 20000 1000
ntp master
ntp server 10.10.10.1
!
end
CallManager#
12-22-2008 05:58 AM
looks like fine from the config point of view except im not getting why there is NO T1/E1 for all your dail-peer !!! local LD and international there are not pointing to anything ??!!
now let me understand you well, if you pick up a phone a call "0" only the 4 FXS ports are ringing ??!!!
if yes try to configure :
ephone-dn x
number 0
call-forward all 100
and make sure you can call 100 directly which is the FXS port !!
hope will help..HTH
12-22-2008 06:20 AM
Actually my analog phone have the number 250
dial-peer voice 76 pots
destination-pattern 250
port 0/1/0
All all extension can call the analog phone
I have put the number "0" to take the FXO port 0/3/0
dial-peer voice 77 pots
destination-pattern 0
port 0/3/0
forward-digits 1
When I dial the number 0 I see an activity on the FXO card but I have no tone
12-22-2008 08:31 AM
now port 0/3/0 is FXO not FXS ?
if yes what are you trying to achive from your setup ?
call 0 as access code to get line then call outside ?
12-22-2008 08:46 AM
Port 0/3/0 = FXO
Port 0/1/0 = FXS
Phone 250 is connected on FXS port 0/1/0 and I want dial 0 to take the line 0/3/0 to send an outgoing call.
12-22-2008 08:59 AM
ok then forward all the dialed digits.
for example for loca calls you will dial 0 then the 7 digits number as below:
dial-peer voice 10 pots
destination-patter 0[2-9]......
port 0/3/0
forward digits 7
try that
12-22-2008 10:34 AM
With it's running
dial-peer voice 77 pots
destination-patter 0[2-9]......
port 0/3/0
forward digits 0
12-22-2008 03:11 PM
your config :
dial-peer voice 77 pots
destination-patter 0[2-9]......
port 0/3/0
forward digits 0 <-- this will not send any digit to FXO, so it wont work.
you need to send the calles number to FXO in order to make your call
regards
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: